virtio_blk: set the zone write granularitygrafted

virtblk_read_zoned_limits() reads the write granularity that the device
reports in virtio_blk_zoned_characteristics and assigns it to the
physical block size and to io_min, but never to the limit that is named
after it. queue_limits.zone_write_granularity is left at zero, so
blk_validate_zoned_limits() raises it to the logical block size:

	if (lim->zone_write_granularity < lim->logical_block_size)
		lim->zone_write_granularity = lim->logical_block_size;

A device that reports a granularity coarser than its logical block size,
which is what the field exists to express, therefore has it silently
reduced. A 512e host managed disk passed through to a guest reports a
logical block size of 512 and a write granularity of 4096, and the guest
ends up with a zone write granularity of 512.

bio_split_alignment() returns lim->zone_write_granularity if it is non-zero
and bio_split_io_at() may split a bio with as per bio_split_alignment().
This can real to the write getting rejected by the host drive, as the write
is not aligned to the physical block size.

zonefs also takes its block size from bdev_zone_write_granularity(), so it
would incorrectly use 512 on a disk that requires 4096.

sd_zbc_read_zones() sets the limit from the physical block size for the
same reason. NVMe ZNS and null_blk leave it unset, but the fallback
gives the right answer for them, as their write granularity is the
logical block size. virtio carries a separate value that may exceed it.

Set the zone write granularity from the value that the device reports.

Fixes: 95bfec41bd3d ("virtio-blk: add support for zoned block devices")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20260918140641.2031075-2-cassel@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 95 insertions, 0 deletions

diff --git a/Documentation/driver-api/pwrseq.rst b/Documentation/driver-api/pwrseq.rst
new file mode 100644
index 000000000..e1056d141
--- /dev/null
+++ b/Documentation/driver-api/pwrseq.rst
@@ -0,0 +1,95 @@
+.. SPDX-License-Identifier: GPL-2.0-only
+.. Copyright 2024 Linaro Ltd.
+
+====================
+Power Sequencing API
+====================
+
+:Author: Bartosz Golaszewski
+
+Introduction
+============
+
+This framework is designed to abstract complex power-up sequences that are
+shared between multiple logical devices in the Linux kernel.
+
+The intention is to allow consumers to obtain a power sequencing handle
+exposed by the power sequence provider and delegate the actual requesting and
+control of the underlying resources as well as to allow the provider to
+mitigate any potential conflicts between multiple users behind the scenes.
+
+Glossary
+--------
+
+The power sequencing API uses a number of terms specific to the subsystem:
+
+Unit
+
+    A unit is a discrete chunk of a power sequence. For instance one unit may
+    enable a set of regulators, another may enable a specific GPIO. Units can
+    define dependencies in the form of other units that must be enabled before
+    it itself can be.
+
+Target
+
+    A target is a set of units (composed of the "final" unit and its
+    dependencies) that a consumer selects by its name when requesting a handle
+    to the power sequencer. Via the dependency system, multiple targets may
+    share the same parts of a power sequence but ignore parts that are
+    irrelevant.
+
+Descriptor
+
+    A handle passed by the pwrseq core to every consumer that serves as the
+    entry point to the provider layer. It ensures coherence between different
+    users and keeps reference counting consistent.
+
+Consumer interface
+==================
+
+The consumer API is aimed to be as simple as possible. The driver interested in
+getting a descriptor from the power sequencer should call pwrseq_get() and
+specify the name of the target it wants to reach in the sequence after calling
+pwrseq_enable(). The descriptor can be released by calling pwrseq_put() and
+the consumer can request the powering down of its target with
+pwrseq_disable(). Note that there is no guarantee that pwrseq_disable()
+will have any effect as there may be multiple users of the underlying resources
+who may keep them active.
+
+Provider interface
+==================
+
+The provider API is admittedly not nearly as straightforward as the one for
+consumers but it makes up for it in flexibility.
+
+Each provider can logically split the power-up sequence into discrete chunks
+(units) and define their dependencies. They can then expose named targets that
+consumers may use as the final point in the sequence that they wish to reach.
+
+To that end the providers fill out a set of configuration structures and
+register with the pwrseq subsystem by calling pwrseq_device_register().
+
+Dynamic consumer matching
+-------------------------
+
+The main difference between pwrseq and other Linux kernel providers is the
+mechanism for dynamic matching of consumers and providers. Every power sequence
+provider driver must implement the `match()` callback and pass it to the pwrseq
+core when registering with the subsystems.
+
+When a client requests a sequencer handle, the core will call this callback for
+every registered provider and let it flexibly figure out whether the proposed
+client device is indeed its consumer. For example: if the provider binds to the
+device-tree node representing a power management unit of a chipset and the
+consumer driver controls one of its modules, the provider driver may parse the
+relevant regulator supply properties in device tree and see if they lead from
+the PMU to the consumer.
+
+API reference
+=============
+
+.. kernel-doc:: include/linux/pwrseq/provider.h
+   :internal:
+
+.. kernel-doc:: drivers/power/sequencing/core.c
+   :export: