iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 91 insertions, 0 deletions

diff --git a/Documentation/driver-api/mmc/mmc-dev-attrs.rst b/Documentation/driver-api/mmc/mmc-dev-attrs.rst
new file mode 100644
index 000000000..4f44b1b73
--- /dev/null
+++ b/Documentation/driver-api/mmc/mmc-dev-attrs.rst
@@ -0,0 +1,91 @@
+==================================
+SD and MMC Block Device Attributes
+==================================
+
+These attributes are defined for the block devices associated with the
+SD or MMC device.
+
+The following attributes are read/write.
+
+	========		===============================================
+	force_ro		Enforce read-only access even if write protect 					switch is off.
+	========		===============================================
+
+SD and MMC Device Attributes
+============================
+
+All attributes are read-only.
+
+	======================	===============================================
+	cid			Card Identification Register
+	csd			Card Specific Data Register
+	scr			SD Card Configuration Register (SD only)
+	date			Manufacturing Date (from CID Register)
+	fwrev			Firmware/Product Revision (from CID Register)
+				(SD and MMCv1 only)
+	hwrev			Hardware/Product Revision (from CID Register)
+				(SD and MMCv1 only)
+	manfid			Manufacturer ID (from CID Register)
+	name			Product Name (from CID Register)
+	oemid			OEM/Application ID (from CID Register)
+	prv			Product Revision (from CID Register)
+				(SD and MMCv4 only)
+	serial			Product Serial Number (from CID Register)
+	erase_size		Erase group size
+	preferred_erase_size	Preferred erase size
+	raw_rpmb_size_mult	RPMB partition size
+	rel_sectors		Reliable write sector count
+	ocr 			Operation Conditions Register
+	dsr			Driver Stage Register
+	cmdq_en			Command Queue enabled:
+
+					1 => enabled, 0 => not enabled
+	======================	===============================================
+
+Note on Erase Size and Preferred Erase Size:
+
+	"erase_size" is the  minimum size, in bytes, of an erase
+	operation.  For MMC, "erase_size" is the erase group size
+	reported by the card.  Note that "erase_size" does not apply
+	to trim or secure trim operations where the minimum size is
+	always one 512 byte sector.  For SD, "erase_size" is 512
+	if the card is block-addressed, 0 otherwise.
+
+	SD/MMC cards can erase an arbitrarily large area up to and
+	including the whole card.  When erasing a large area it may
+	be desirable to do it in smaller chunks for three reasons:
+
+	     1. A single erase command will make all other I/O on
+		the card wait.  This is not a problem if the whole card
+		is being erased, but erasing one partition will make
+		I/O for another partition on the same card wait for the
+		duration of the erase - which could be a several
+		minutes.
+	     2. To be able to inform the user of erase progress.
+	     3. The erase timeout becomes too large to be very
+		useful.  Because the erase timeout contains a margin
+		which is multiplied by the size of the erase area,
+		the value can end up being several minutes for large
+		areas.
+
+	"erase_size" is not the most efficient unit to erase
+	(especially for SD where it is just one sector),
+	hence "preferred_erase_size" provides a good chunk
+	size for erasing large areas.
+
+	For MMC, "preferred_erase_size" is the high-capacity
+	erase size if a card specifies one, otherwise it is
+	based on the capacity of the card.
+
+	For SD, "preferred_erase_size" is the allocation unit
+	size specified by the card.
+
+	"preferred_erase_size" is in bytes.
+
+Note on raw_rpmb_size_mult:
+
+	"raw_rpmb_size_mult" is a multiple of 128kB block.
+
+	RPMB size in byte is calculated by using the following equation:
+
+		RPMB partition size = 128kB x raw_rpmb_size_mult