Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 109 insertions, 0 deletions

diff --git a/Documentation/driver-api/ipmb.rst b/Documentation/driver-api/ipmb.rst
new file mode 100644
index 000000000..209c49e05
--- /dev/null
+++ b/Documentation/driver-api/ipmb.rst
@@ -0,0 +1,109 @@
+==============================
+IPMB Driver for a Satellite MC
+==============================
+
+The Intelligent Platform Management Bus or IPMB, is an
+I2C bus that provides a standardized interconnection between
+different boards within a chassis. This interconnection is
+between the baseboard management (BMC) and chassis electronics.
+IPMB is also associated with the messaging protocol through the
+IPMB bus.
+
+The devices using the IPMB are usually management
+controllers that perform management functions such as servicing
+the front panel interface, monitoring the baseboard,
+hot-swapping disk drivers in the system chassis, etc...
+
+When an IPMB is implemented in the system, the BMC serves as
+a controller to give system software access to the IPMB. The BMC
+sends IPMI requests to a device (usually a Satellite Management
+Controller or Satellite MC) via IPMB and the device
+sends a response back to the BMC.
+
+For more information on IPMB and the format of an IPMB message,
+refer to the IPMB and IPMI specifications.
+
+IPMB driver for Satellite MC
+----------------------------
+
+ipmb-dev-int - This is the driver needed on a Satellite MC to
+receive IPMB messages from a BMC and send a response back.
+This driver works with the I2C driver and a userspace
+program such as OpenIPMI:
+
+1) It is an I2C slave backend driver. So, it defines a callback
+   function to set the Satellite MC as an I2C slave.
+   This callback function handles the received IPMI requests.
+
+2) It defines the read and write functions to enable a user
+   space program (such as OpenIPMI) to communicate with the kernel.
+
+
+Load the IPMB driver
+--------------------
+
+The driver needs to be loaded at boot time or manually first.
+First, make sure you have the following in your config file:
+CONFIG_IPMB_DEVICE_INTERFACE=y
+
+1) If you want the driver to be loaded at boot time:
+
+a) Add this entry to your ACPI table, under the appropriate SMBus::
+
+     Device (SMB0) // Example SMBus host controller
+     {
+     Name (_HID, "<Vendor-Specific HID>") // Vendor-Specific HID
+     Name (_UID, 0) // Unique ID of particular host controller
+     :
+     :
+       Device (IPMB)
+       {
+         Name (_HID, "IPMB0001") // IPMB device interface
+         Name (_UID, 0) // Unique device identifier
+       }
+     }
+
+b) Example for device tree::
+
+     &i2c2 {
+            status = "okay";
+
+            ipmb@10 {
+                    compatible = "ipmb-dev";
+                    reg = <0x10>;
+                    i2c-protocol;
+            };
+     };
+
+If xmit of data to be done using raw i2c block vs smbus
+then "i2c-protocol" needs to be defined as above.
+
+2) Manually from Linux::
+
+     modprobe ipmb-dev-int
+
+
+Instantiate the device
+----------------------
+
+After loading the driver, you can instantiate the device as
+described in 'Documentation/i2c/instantiating-devices.rst'.
+If you have multiple BMCs, each connected to your Satellite MC via
+a different I2C bus, you can instantiate a device for each of
+those BMCs.
+
+The name of the instantiated device contains the I2C bus number
+associated with it as follows::
+
+  BMC1 ------ IPMB/I2C bus 1 ---------|   /dev/ipmb-1
+				Satellite MC
+  BMC1 ------ IPMB/I2C bus 2 ---------|   /dev/ipmb-2
+
+For instance, you can instantiate the ipmb-dev-int device from
+user space at the 7 bit address 0x10 on bus 2::
+
+  # echo ipmb-dev 0x1010 > /sys/bus/i2c/devices/i2c-2/new_device
+
+This will create the device file /dev/ipmb-2, which can be accessed
+by the user space program. The device needs to be instantiated
+before running the user space program.