sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling buggrafted

alb_break_llc() decides whether to break LLC preference during active
load balance. It does so by testing that every runnable fair task on the
source rq prefers its LLC:

	env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable

But the two counters cover different sets. nr_pref_llc_running is updated
in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued,
so it follows queued tasks. h_nr_runnable is updated in set_delayed()/
clear_delayed() and drops delay-dequeued tasks.

So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted
in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks,
alb_break_llc() returns false, and active balance is free to pull a task
off its preferred LLC. Active balance only moves runnable tasks, and this
is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB
skips the per-task test in can_migrate_task(). The runnable set is the one
we want.

Fix it on the counter side. A task should be counted in
nr_pref_llc_running exactly while it is both queued on its preferred LLC
(pref_llc_queued) and runnable (!sched_delayed). Define that membership
once in task_pref_llc_runnable(), and adjust the counter only through
pref_llc_running_inc()/pref_llc_running_dec() from the four sites that
change either input: account_llc_enqueue(), account_llc_dequeue(),
set_delayed() and clear_delayed(). Gating every update on the same
predicate keeps the delay, wake and dequeue paths from double-counting
or underflowing; see the comments at those sites for the ordering.

nr_llc_running and sd->llc_counts are not touched and stay on queued
semantics.

Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC")
Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/
Reported-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kayra Cizmeci <kayracizmeci@gmail.com>
Cc: <stable@kernel.org> # v7.2.x
Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com

1 files changed, 48 insertions, 0 deletions

diff --git a/Documentation/driver-api/i2c.rst b/Documentation/driver-api/i2c.rst
new file mode 100644
index 000000000..7582c079d
--- /dev/null
+++ b/Documentation/driver-api/i2c.rst
@@ -0,0 +1,48 @@
+I\ :sup:`2`\ C and SMBus Subsystem
+==================================
+
+I\ :sup:`2`\ C (or without fancy typography, "I2C") is an acronym for
+the "Inter-IC" bus, a simple bus protocol which is widely used where low
+data rate communications suffice. Since it's also a licensed trademark,
+some vendors use another name (such as "Two-Wire Interface", TWI) for
+the same bus. I2C only needs two signals (SCL for clock, SDA for data),
+conserving board real estate and minimizing signal quality issues. Most
+I2C devices use seven bit addresses, and bus speeds of up to 400 kHz;
+there's a high speed extension (3.4 MHz) that's not yet found wide use.
+I2C is a multi-master bus; open drain signaling is used to arbitrate
+between masters, as well as to handshake and to synchronize clocks from
+slower clients.
+
+The Linux I2C programming interfaces support the master side of bus
+interactions and the slave side. The programming interface is
+structured around two kinds of driver, and two kinds of device. An I2C
+"Adapter Driver" abstracts the controller hardware; it binds to a
+physical device (perhaps a PCI device or platform_device) and exposes a
+:c:type:`struct i2c_adapter <i2c_adapter>` representing each
+I2C bus segment it manages. On each I2C bus segment will be I2C devices
+represented by a :c:type:`struct i2c_client <i2c_client>`.
+Those devices will be bound to a :c:type:`struct i2c_driver
+<i2c_driver>`, which should follow the standard Linux driver model. There
+are functions to perform various I2C protocol operations; at this writing
+all such functions are usable only from task context.
+
+The System Management Bus (SMBus) is a sibling protocol. Most SMBus
+systems are also I2C conformant. The electrical constraints are tighter
+for SMBus, and it standardizes particular protocol messages and idioms.
+Controllers that support I2C can also support most SMBus operations, but
+SMBus controllers don't support all the protocol options that an I2C
+controller will. There are functions to perform various SMBus protocol
+operations, either using I2C primitives or by issuing SMBus commands to
+i2c_adapter devices which don't support those I2C operations.
+
+.. kernel-doc:: include/linux/i2c.h
+   :internal:
+
+.. kernel-doc:: drivers/i2c/i2c-boardinfo.c
+   :functions: i2c_register_board_info
+
+.. kernel-doc:: drivers/i2c/i2c-core-base.c
+   :export:
+
+.. kernel-doc:: drivers/i2c/i2c-core-smbus.c
+   :export: