drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 88 insertions, 0 deletions

diff --git a/Documentation/driver-api/hsi.rst b/Documentation/driver-api/hsi.rst
new file mode 100644
index 000000000..01b6bebfb
--- /dev/null
+++ b/Documentation/driver-api/hsi.rst
@@ -0,0 +1,88 @@
+High Speed Synchronous Serial Interface (HSI)
+=============================================
+
+Introduction
+---------------
+
+High Speed Synchronous Interface (HSI) is a full duplex, low latency protocol,
+that is optimized for die-level interconnect between an Application Processor
+and a Baseband chipset. It has been specified by the MIPI alliance in 2003 and
+implemented by multiple vendors since then.
+
+The HSI interface supports full duplex communication over multiple channels
+(typically 8) and is capable of reaching speeds up to 200 Mbit/s.
+
+The serial protocol uses two signals, DATA and FLAG as combined data and clock
+signals and an additional READY signal for flow control. An additional WAKE
+signal can be used to wakeup the chips from standby modes. The signals are
+commonly prefixed by AC for signals going from the application die to the
+cellular die and CA for signals going the other way around.
+
+::
+
+    +------------+                                 +---------------+
+    |  Cellular  |                                 |  Application  |
+    |    Die     |                                 |      Die      |
+    |            | - - - - - - CAWAKE - - - - - - >|               |
+    |           T|------------ CADATA ------------>|R              |
+    |           X|------------ CAFLAG ------------>|X              |
+    |            |<----------- ACREADY ------------|               |
+    |            |                                 |               |
+    |            |                                 |               |
+    |            |< - - - - -  ACWAKE - - - - - - -|               |
+    |           R|<----------- ACDATA -------------|T              |
+    |           X|<----------- ACFLAG -------------|X              |
+    |            |------------ CAREADY ----------->|               |
+    |            |                                 |               |
+    |            |                                 |               |
+    +------------+                                 +---------------+
+
+HSI Subsystem in Linux
+-------------------------
+
+In the Linux kernel the hsi subsystem is supposed to be used for HSI devices.
+The hsi subsystem contains drivers for hsi controllers including support for
+multi-port controllers and provides a generic API for using the HSI ports.
+
+It also contains HSI client drivers, which make use of the generic API to
+implement a protocol used on the HSI interface. These client drivers can
+use an arbitrary number of channels.
+
+hsi-char Device
+------------------
+
+Each port automatically registers a generic client driver called hsi_char,
+which provides a character device for userspace representing the HSI port.
+It can be used to communicate via HSI from userspace. Userspace may
+configure the hsi_char device using the following ioctl commands:
+
+HSC_RESET
+ flush the HSI port
+
+HSC_SET_PM
+ enable or disable the client.
+
+HSC_SEND_BREAK
+ send break
+
+HSC_SET_RX
+ set RX configuration
+
+HSC_GET_RX
+ get RX configuration
+
+HSC_SET_TX
+ set TX configuration
+
+HSC_GET_TX
+ get TX configuration
+
+The kernel HSI API
+------------------
+
+.. kernel-doc:: include/linux/hsi/hsi.h
+   :internal:
+
+.. kernel-doc:: drivers/hsi/hsi_core.c
+   :export:
+