virtio_blk: set the zone write granularitygrafted

virtblk_read_zoned_limits() reads the write granularity that the device
reports in virtio_blk_zoned_characteristics and assigns it to the
physical block size and to io_min, but never to the limit that is named
after it. queue_limits.zone_write_granularity is left at zero, so
blk_validate_zoned_limits() raises it to the logical block size:

	if (lim->zone_write_granularity < lim->logical_block_size)
		lim->zone_write_granularity = lim->logical_block_size;

A device that reports a granularity coarser than its logical block size,
which is what the field exists to express, therefore has it silently
reduced. A 512e host managed disk passed through to a guest reports a
logical block size of 512 and a write granularity of 4096, and the guest
ends up with a zone write granularity of 512.

bio_split_alignment() returns lim->zone_write_granularity if it is non-zero
and bio_split_io_at() may split a bio with as per bio_split_alignment().
This can real to the write getting rejected by the host drive, as the write
is not aligned to the physical block size.

zonefs also takes its block size from bdev_zone_write_granularity(), so it
would incorrectly use 512 on a disk that requires 4096.

sd_zbc_read_zones() sets the limit from the physical block size for the
same reason. NVMe ZNS and null_blk leave it unset, but the fallback
gives the right answer for them, as their write granularity is the
logical block size. virtio carries a separate value that may exceed it.

Set the zone write granularity from the value that the device reports.

Fixes: 95bfec41bd3d ("virtio-blk: add support for zoned block devices")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20260918140641.2031075-2-cassel@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 81 insertions, 0 deletions

diff --git a/Documentation/driver-api/backlight/lp855x-driver.rst b/Documentation/driver-api/backlight/lp855x-driver.rst
new file mode 100644
index 000000000..1e0b224fc
--- /dev/null
+++ b/Documentation/driver-api/backlight/lp855x-driver.rst
@@ -0,0 +1,81 @@
+====================
+Kernel driver lp855x
+====================
+
+Backlight driver for LP855x ICs
+
+Supported chips:
+
+	Texas Instruments LP8550, LP8551, LP8552, LP8553, LP8555, LP8556 and
+	LP8557
+
+Author: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+-----------
+
+* Brightness control
+
+  Brightness can be controlled by the pwm input or the i2c command.
+  The lp855x driver supports both cases.
+
+* Device attributes
+
+  1) bl_ctl_mode
+
+  Backlight control mode.
+
+  Value: pwm based or register based
+
+  2) chip_id
+
+  The lp855x chip id.
+
+  Value: lp8550/lp8551/lp8552/lp8553/lp8555/lp8556/lp8557
+
+Platform data for lp855x
+------------------------
+
+For supporting platform specific data, the lp855x platform data can be used.
+
+* name:
+	Backlight driver name. If it is not defined, default name is set.
+* device_control:
+	Value of DEVICE CONTROL register.
+* initial_brightness:
+	Initial value of backlight brightness.
+* period_ns:
+	Platform specific PWM period value. unit is nano.
+	Only valid when brightness is pwm input mode.
+* size_program:
+	Total size of lp855x_rom_data.
+* rom_data:
+	List of new eeprom/eprom registers.
+
+Examples
+========
+
+1) lp8552 platform data: i2c register mode with new eeprom data::
+
+    #define EEPROM_A5_ADDR	0xA5
+    #define EEPROM_A5_VAL	0x4f	/* EN_VSYNC=0 */
+
+    static struct lp855x_rom_data lp8552_eeprom_arr[] = {
+	{EEPROM_A5_ADDR, EEPROM_A5_VAL},
+    };
+
+    static struct lp855x_platform_data lp8552_pdata = {
+	.name = "lcd-bl",
+	.device_control = I2C_CONFIG(LP8552),
+	.initial_brightness = INITIAL_BRT,
+	.size_program = ARRAY_SIZE(lp8552_eeprom_arr),
+	.rom_data = lp8552_eeprom_arr,
+    };
+
+2) lp8556 platform data: pwm input mode with default rom data::
+
+    static struct lp855x_platform_data lp8556_pdata = {
+	.device_control = PWM_CONFIG(LP8556),
+	.initial_brightness = INITIAL_BRT,
+	.period_ns = 1000000,
+    };