arm64/boot: Disable trapping of PMZR_EL0 writes to EL2grafted

__init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2.
PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in
HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host
traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The
kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU
driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a
write from EL0 reaches the trap and takes the host down without a panic
message.

Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already
does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9
bits.

Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9")
Cc: stable@vger.kernel.org
Signed-off-by: Fuad Tabba <fuad.tabba@linux.dev>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Oliver Upton <oupton@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

1 files changed, 37 insertions, 0 deletions

diff --git a/Documentation/devicetree/changesets.rst b/Documentation/devicetree/changesets.rst
new file mode 100644
index 000000000..2091468d4
--- /dev/null
+++ b/Documentation/devicetree/changesets.rst
@@ -0,0 +1,37 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================
+Devicetree Changesets
+=====================
+
+A Devicetree changeset is a method which allows one to apply changes
+in the live tree in such a way that either the full set of changes
+will be applied, or none of them will be. If an error occurs partway
+through applying the changeset, then the tree will be rolled back to the
+previous state. A changeset can also be removed after it has been
+applied.
+
+When a changeset is applied, all of the changes get applied to the tree
+at once before emitting OF_RECONFIG notifiers. This is so that the
+receiver sees a complete and consistent state of the tree when it
+receives the notifier.
+
+The sequence of a changeset is as follows.
+
+1. of_changeset_init() - initializes a changeset
+
+2. A number of DT tree change calls, of_changeset_attach_node(),
+   of_changeset_detach_node(), of_changeset_add_property(),
+   of_changeset_remove_property, of_changeset_update_property() to prepare
+   a set of changes. No changes to the active tree are made at this point.
+   All the change operations are recorded in the of_changeset 'entries'
+   list.
+
+3. of_changeset_apply() - Apply the changes to the tree. Either the
+   entire changeset will get applied, or if there is an error the tree will
+   be restored to the previous state. The core ensures proper serialization
+   through locking. An unlocked version __of_changeset_apply is available,
+   if needed.
+
+If a successfully applied changeset needs to be removed, it can be done
+with of_changeset_revert().