iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 84 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml b/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml
new file mode 100644
index 000000000..99e2865f0
--- /dev/null
+++ b/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/access-controllers/access-controllers.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Domain Access Controllers
+
+maintainers:
+  - Oleksii Moisieiev <oleksii_moisieiev@epam.com>
+
+description: |+
+  Common access controllers properties
+
+  Access controllers are in charge of stating which of the hardware blocks under
+  their responsibility (their domain) can be accesssed by which compartment. A
+  compartment can be a cluster of CPUs (or coprocessors), a range of addresses
+  or a group of hardware blocks. An access controller's domain is the set of
+  resources covered by the access controller.
+
+  This device tree binding can be used to bind devices to their access
+  controller provided by access-controllers property. In this case, the device
+  is a consumer and the access controller is the provider.
+
+  An access controller can be represented by any node in the device tree and
+  can provide one or more configuration parameters, needed to control parameters
+  of the consumer device. A consumer node can refer to the provider by phandle
+  and a set of phandle arguments, specified by '#access-controller-cells'
+  property in the access controller node.
+
+  Access controllers are typically used to set/read the permissions of a
+  hardware block and grant access to it. Any of which depends on the access
+  controller. The capabilities of each access controller are defined by the
+  binding of the access controller device.
+
+  Each node can be a consumer for the several access controllers.
+
+# always select the core schema
+select: true
+
+properties:
+  "#access-controller-cells":
+    description:
+      Number of cells in an access-controllers specifier;
+      Can be any value as specified by device tree binding documentation
+      of a particular provider. The node is an access controller.
+
+  access-controller-names:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    description:
+      A list of access-controllers names, sorted in the same order as
+      access-controllers entries. Consumer drivers will use
+      access-controller-names to match with existing access-controllers entries.
+
+  access-controllers:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      A list of access controller specifiers, as defined by the
+      bindings of the access-controllers provider.
+
+additionalProperties: true
+
+examples:
+  - |
+    clock_controller: access-controllers@50000 {
+        reg = <0x50000 0x400>;
+        #access-controller-cells = <2>;
+    };
+
+    bus_controller: bus@60000 {
+        reg = <0x60000 0x10000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+        #access-controller-cells = <3>;
+
+        uart4: serial@60100 {
+            reg = <0x60100 0x400>;
+            clocks = <&clk_serial>;
+            access-controllers = <&clock_controller 1 2>,
+                                 <&bus_controller 1 3 5>;
+            access-controller-names = "clock", "bus";
+        };
+    };