Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 62 insertions, 0 deletions

diff --git a/Documentation/admin-guide/vga-softcursor.rst b/Documentation/admin-guide/vga-softcursor.rst
new file mode 100644
index 000000000..f52175457
--- /dev/null
+++ b/Documentation/admin-guide/vga-softcursor.rst
@@ -0,0 +1,62 @@
+Software cursor for VGA
+=======================
+
+by Pavel Machek <pavel@atrey.karlin.mff.cuni.cz>
+and Martin Mares <mj@atrey.karlin.mff.cuni.cz>
+
+Linux now has some ability to manipulate cursor appearance.  Normally,
+you can set the size of hardware cursor.  You can now play a few new
+tricks: you can make your cursor look like a non-blinking red block,
+make it inverse background of the character it's over or to highlight
+that character and still choose whether the original hardware cursor
+should remain visible or not.  There may be other things I have never
+thought of.
+
+The cursor appearance is controlled by a ``<ESC>[?1;2;3c`` escape sequence
+where 1, 2 and 3 are parameters described below. If you omit any of them,
+they will default to zeroes.
+
+first Parameter
+	specifies cursor size::
+
+		0=default
+		1=invisible
+		2=underline,
+		...
+		8=full block
+		+ 16 if you want the software cursor to be applied
+		+ 32 if you want to always change the background color
+		+ 64 if you dislike having the background the same as the
+		     foreground.
+
+	Highlights are ignored for the last two flags.
+
+second parameter
+	selects character attribute bits you want to change
+	(by simply XORing them with the value of this parameter). On standard
+	VGA, the high four bits specify background and the low four the
+	foreground. In both groups, low three bits set color (as in normal
+	color codes used by the console) and the most significant one turns
+	on highlight (or sometimes blinking -- it depends on the configuration
+	of your VGA).
+
+third parameter
+	consists of character attribute bits you want to set.
+
+	Bit setting takes place before bit toggling, so you can simply clear a
+	bit by including it in both the set mask and the toggle mask.
+
+Examples
+--------
+
+To get normal blinking underline, use::
+
+	echo -e '\033[?2c'
+
+To get blinking block, use::
+
+	echo -e '\033[?6c'
+
+To get red non-blinking block, use::
+
+	echo -e '\033[?17;0;64c'