drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 52 insertions, 0 deletions

diff --git a/Documentation/admin-guide/sysctl/debug.rst b/Documentation/admin-guide/sysctl/debug.rst
new file mode 100644
index 000000000..506bd5e48
--- /dev/null
+++ b/Documentation/admin-guide/sysctl/debug.rst
@@ -0,0 +1,52 @@
+================
+/proc/sys/debug/
+================
+
+These files show up in ``/proc/sys/debug/``, depending on the
+kernel configuration:
+
+.. contents:: :local:
+
+exception-trace
+===============
+
+This flag controls whether the kernel prints information about unhandled
+signals (like segmentation faults) to the kernel log (``dmesg``).
+
+- ``0``: Unhandled signals are not traced.
+- ``1``: Information about unhandled signals is printed.
+
+The default value is ``1`` on most architectures (like x86, MIPS, RISC-V),
+but it is ``0`` on **arm64**.
+
+The actual information printed and the context provided varies
+significantly depending on the CPU architecture. For example:
+
+- On **x86**, it typically prints the instruction pointer (IP), error
+  code, and address that caused a page fault.
+- On **PowerPC**, it may print the next instruction pointer (NIP),
+  link register (LR), and other relevant registers.
+
+When enabled, this feature is often rate-limited to prevent the kernel
+log from being flooded during a crash loop.
+
+kprobes-optimization
+====================
+
+This flag enables or disables the optimization of Kprobes on certain
+architectures (like x86).
+
+- ``0``: Kprobes optimization is turned off.
+- ``1``: Kprobes optimization is turned on (default).
+
+For more details on Kprobes and its optimization, please refer to
+Documentation/trace/kprobes.rst.
+
+Copyright (c) 2026, Shubham Chakraborty <chakrabortyshubham66@gmail.com>
+
+For general info and legal blurb, please look in
+Documentation/admin-guide/sysctl/index.rst.
+
+.. See scripts/check-sysctl-docs to keep this up to date:
+.. scripts/check-sysctl-docs -vtable="debug" \
+..         $(git grep -l register_sysctl_)