drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 48 insertions, 0 deletions

diff --git a/Documentation/admin-guide/init.rst b/Documentation/admin-guide/init.rst
new file mode 100644
index 000000000..41f06a091
--- /dev/null
+++ b/Documentation/admin-guide/init.rst
@@ -0,0 +1,48 @@
+Explaining the "No working init found." boot hang message
+=========================================================
+:Authors: Andreas Mohr <andi at lisas period de>
+          Cristian Souza <cristianmsbr at gmail period com>
+
+This document provides some high-level reasons for failure
+(listed roughly in order of execution) to load the init binary.
+
+1) **Unable to mount root FS**: Set "debug" kernel parameter (in bootloader
+   config file or CONFIG_CMDLINE) to get more detailed kernel messages.
+
+2) **init binary doesn't exist on rootfs**: Make sure you have the correct
+   root FS type (and ``root=`` kernel parameter points to the correct
+   partition), required drivers such as storage hardware (such as SCSI or
+   USB!) and filesystem (ext3, jffs2, etc.) are builtin (alternatively as
+   modules, to be pre-loaded by an initrd).
+
+3) **Broken console device**: Possibly a conflict in ``console= setup``
+   --> initial console unavailable. E.g. some serial consoles are unreliable
+   due to serial IRQ issues (e.g. missing interrupt-based configuration).
+   Try using a different ``console= device`` or e.g. ``netconsole=``.
+
+4) **Binary exists but dependencies not available**: E.g. required library
+   dependencies of the init binary such as ``/lib/ld-linux.so.2`` missing or
+   broken. Use ``readelf -d <INIT>|grep NEEDED`` to find out which libraries
+   are required.
+
+5) **Binary cannot be loaded**: Make sure the binary's architecture matches
+   your hardware. E.g. i386 vs. x86_64 mismatch, or trying to load x86 on ARM
+   hardware. In case you tried loading a non-binary file here (shell script?),
+   you should make sure that the script specifies an interpreter in its
+   shebang header line (``#!/...``) that is fully working (including its
+   library dependencies). And before tackling scripts, better first test a
+   simple non-script binary such as ``/bin/sh`` and confirm its successful
+   execution. To find out more, add code ``to init/main.c`` to display
+   kernel_execve()s return values.
+
+Please extend this explanation whenever you find new failure causes
+(after all loading the init binary is a CRITICAL and hard transition step
+which needs to be made as painless as possible), then submit a patch to LKML.
+Further TODOs:
+
+- Implement the various ``run_init_process()`` invocations via a struct array
+  which can then store the ``kernel_execve()`` result value and on failure
+  log it all by iterating over **all** results (very important usability fix).
+- Try to make the implementation itself more helpful in general, e.g. by
+  providing additional error messages at affected places.
+