iio: proximity: vl53l0x-i2c: claim direct mode for raw readsgrafted

vl53l0x_read_raw() starts a single-shot ranging measurement and reads
back the result. Once the triggered buffer is enabled the sensor runs in
continuous mode and its data-ready interrupt is routed to the trigger,
so a concurrent in_distance_raw read disturbs the streaming setup and
never gets its completion, returning -ETIMEDOUT.

The original submission claimed direct mode here, but it was dropped
during review because the driver had no buffer support at the time [1].
Continuous (buffered) mode was later added without restoring the
claim [2], reintroducing the conflict.

Reject direct reads while buffered capture is active by claiming direct
mode around the measurement, as the vl53l1x sibling already does.

Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support")
Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1]
Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2]
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

1 files changed, 37 insertions, 0 deletions

diff --git a/Documentation/admin-guide/device-mapper/zero.rst b/Documentation/admin-guide/device-mapper/zero.rst
new file mode 100644
index 000000000..11fb5cf45
--- /dev/null
+++ b/Documentation/admin-guide/device-mapper/zero.rst
@@ -0,0 +1,37 @@
+=======
+dm-zero
+=======
+
+Device-Mapper's "zero" target provides a block-device that always returns
+zero'd data on reads and silently drops writes. This is similar behavior to
+/dev/zero, but as a block-device instead of a character-device.
+
+Dm-zero has no target-specific parameters.
+
+One very interesting use of dm-zero is for creating "sparse" devices in
+conjunction with dm-snapshot. A sparse device reports a device-size larger
+than the amount of actual storage space available for that device. A user can
+write data anywhere within the sparse device and read it back like a normal
+device. Reads to previously unwritten areas will return a zero'd buffer. When
+enough data has been written to fill up the actual storage space, the sparse
+device is deactivated. This can be very useful for testing device and
+filesystem limitations.
+
+To create a sparse device, start by creating a dm-zero device that's the
+desired size of the sparse device. For this example, we'll assume a 10TB
+sparse device::
+
+  TEN_TERABYTES=`expr 10 \* 1024 \* 1024 \* 1024 \* 2`   # 10 TB in sectors
+  echo "0 $TEN_TERABYTES zero" | dmsetup create zero1
+
+Then create a snapshot of the zero device, using any available block-device as
+the COW device. The size of the COW device will determine the amount of real
+space available to the sparse device. For this example, we'll assume /dev/sdb1
+is an available 10GB partition::
+
+  echo "0 $TEN_TERABYTES snapshot /dev/mapper/zero1 /dev/sdb1 p 128" | \
+     dmsetup create sparse1
+
+This will create a 10TB sparse device called /dev/mapper/sparse1 that has
+10GB of actual storage space available. If more than 10GB of data is written
+to this device, it will start returning I/O errors.