drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validationgrafted

amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and
uses the first encoding that validates. YCbCr 4:4:4 is listed before
RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the
"color format" property is left at AUTO, even though RGB fits the same
link.

That contradicts the documented AUTO behaviour for HDMI in enum
drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when
the bandwidth is not available or the mode is 4:2:0-only), which the
amdgpu implementation of the property also describes. It also leaves
the "Broadcast RGB" property without effect on such sinks, since the
quantization range it selects only applies to RGB output.

Try RGB first. The mask still holds every encoding the sink supports,
so a mode that cannot carry RGB falls back exactly as before.

For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced
through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI
sink that advertised it.

Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation")
Suggested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Assisted-by: Claude Code:claude-fable-5-1
Signed-off-by: Adrian Betschart <adrian.betschart@cinemaone.ch>
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Adolfo Rodrigues <adolfotregosa@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7)

1 files changed, 37 insertions, 0 deletions

diff --git a/Documentation/admin-guide/device-mapper/zero.rst b/Documentation/admin-guide/device-mapper/zero.rst
new file mode 100644
index 000000000..11fb5cf45
--- /dev/null
+++ b/Documentation/admin-guide/device-mapper/zero.rst
@@ -0,0 +1,37 @@
+=======
+dm-zero
+=======
+
+Device-Mapper's "zero" target provides a block-device that always returns
+zero'd data on reads and silently drops writes. This is similar behavior to
+/dev/zero, but as a block-device instead of a character-device.
+
+Dm-zero has no target-specific parameters.
+
+One very interesting use of dm-zero is for creating "sparse" devices in
+conjunction with dm-snapshot. A sparse device reports a device-size larger
+than the amount of actual storage space available for that device. A user can
+write data anywhere within the sparse device and read it back like a normal
+device. Reads to previously unwritten areas will return a zero'd buffer. When
+enough data has been written to fill up the actual storage space, the sparse
+device is deactivated. This can be very useful for testing device and
+filesystem limitations.
+
+To create a sparse device, start by creating a dm-zero device that's the
+desired size of the sparse device. For this example, we'll assume a 10TB
+sparse device::
+
+  TEN_TERABYTES=`expr 10 \* 1024 \* 1024 \* 1024 \* 2`   # 10 TB in sectors
+  echo "0 $TEN_TERABYTES zero" | dmsetup create zero1
+
+Then create a snapshot of the zero device, using any available block-device as
+the COW device. The size of the COW device will determine the amount of real
+space available to the sparse device. For this example, we'll assume /dev/sdb1
+is an available 10GB partition::
+
+  echo "0 $TEN_TERABYTES snapshot /dev/mapper/zero1 /dev/sdb1 p 128" | \
+     dmsetup create sparse1
+
+This will create a 10TB sparse device called /dev/mapper/sparse1 that has
+10GB of actual storage space available. If more than 10GB of data is written
+to this device, it will start returning I/O errors.