Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 38 insertions, 0 deletions

diff --git a/Documentation/admin-guide/braille-console.rst b/Documentation/admin-guide/braille-console.rst
new file mode 100644
index 000000000..153472e93
--- /dev/null
+++ b/Documentation/admin-guide/braille-console.rst
@@ -0,0 +1,38 @@
+Linux Braille Console
+=====================
+
+To get early boot messages on a braille device (before userspace screen
+readers can start), you first need to compile the support for the usual serial
+console (see :ref:`Documentation/admin-guide/serial-console.rst <serial_console>`), and
+for braille device
+(in :menuselection:`Device Drivers --> Accessibility support --> Console on braille device`).
+
+Then you need to specify a ``console=brl``, option on the kernel command line, the
+format is::
+
+	console=brl,serial_options...
+
+where ``serial_options...`` are the same as described in
+:ref:`Documentation/admin-guide/serial-console.rst <serial_console>`.
+
+So for instance you can use ``console=brl,ttyS0`` if the braille device is connected to the first serial port, and ``console=brl,ttyS0,115200`` to
+override the baud rate to 115200, etc.
+
+By default, the braille device will just show the last kernel message (console
+mode).  To review previous messages, press the Insert key to switch to the VT
+review mode.  In review mode, the arrow keys permit to browse in the VT content,
+`PAGE-UP`/`PAGE-DOWN` keys go at the top/bottom of the screen, and
+the `HOME` key goes back
+to the cursor, hence providing very basic screen reviewing facility.
+
+Sound feedback can be obtained by adding the ``braille_console.sound=1`` kernel
+parameter.
+
+For simplicity, only one braille console can be enabled, other uses of
+``console=brl,...`` will be discarded.  Also note that it does not interfere with
+the console selection mechanism described in
+:ref:`Documentation/admin-guide/serial-console.rst <serial_console>`.
+
+For now, only the VisioBraille device is supported.
+
+Samuel Thibault <samuel.thibault@ens-lyon.org>