ftrace: Synchronize the initialization of ftrace_opsgrafted

There's some internal state that ftrace_ops needs to have set, but since
it can be declared outside of the ftrace.c code, it calls
ftrace_ops_init() on the ops in every global function. The issue is that
if two tasks call it on the same ops at the same time it is possible to
have the initialization of one corrupt the initialization of the other
call.

Create a ops_mutex to use to synchronize every initialization of the
ftrace_ops. The mutex is taken within checking the ftrace_ops flag that
states it was initializied but the flag is checked again after the mutex
has been taken. Checking first outside the mutex allows it to shortcut
having to take the mutex. But then the check needs to be done again after
the mute is taken in case of races.

Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260902095501.6b59af20@gandalf.local.home
Fixes: f04f24fb7e48d ("ftrace, kprobes: Fix a deadlock on ftrace_regex_lock")
Reported-by: sashiko-bot@kernel.org
Close: https://lore.kernel.org/all/20260829025528.49A831F000E9@smtp.kernel.org/
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

3 files changed, 157 insertions, 0 deletions

diff --git a/Documentation/admin-guide/auxdisplay/cfag12864b.rst b/Documentation/admin-guide/auxdisplay/cfag12864b.rst
new file mode 100644
index 000000000..da385d851
--- /dev/null
+++ b/Documentation/admin-guide/auxdisplay/cfag12864b.rst
@@ -0,0 +1,98 @@
+===================================
+cfag12864b LCD Driver Documentation
+===================================
+
+:License:		GPLv2
+:Author & Maintainer:	Miguel Ojeda <ojeda@kernel.org>
+:Date:			2006-10-27
+
+
+
+.. INDEX
+
+	1. DRIVER INFORMATION
+	2. DEVICE INFORMATION
+	3. WIRING
+	4. USERSPACE PROGRAMMING
+
+1. Driver Information
+---------------------
+
+This driver supports a cfag12864b LCD.
+
+
+2. Device Information
+---------------------
+
+:Manufacturer:	Crystalfontz
+:Device Name:	Crystalfontz 12864b LCD Series
+:Device Code:	cfag12864b
+:Webpage:	http://www.crystalfontz.com
+:Device Webpage: http://www.crystalfontz.com/products/12864b/
+:Type:		LCD (Liquid Crystal Display)
+:Width:		128
+:Height:	64
+:Colors:	2 (B/N)
+:Controller:	ks0108
+:Controllers:	2
+:Pages:		8 each controller
+:Addresses:	64 each page
+:Data size:	1 byte each address
+:Memory size:	2 * 8 * 64 * 1 = 1024 bytes = 1 Kbyte
+
+
+3. Wiring
+---------
+
+The cfag12864b LCD Series don't have official wiring.
+
+The common wiring is done to the parallel port as shown::
+
+  Parallel Port                          cfag12864b
+
+    Name Pin#                            Pin# Name
+
+  Strobe ( 1)------------------------------(17) Enable
+  Data 0 ( 2)------------------------------( 4) Data 0
+  Data 1 ( 3)------------------------------( 5) Data 1
+  Data 2 ( 4)------------------------------( 6) Data 2
+  Data 3 ( 5)------------------------------( 7) Data 3
+  Data 4 ( 6)------------------------------( 8) Data 4
+  Data 5 ( 7)------------------------------( 9) Data 5
+  Data 6 ( 8)------------------------------(10) Data 6
+  Data 7 ( 9)------------------------------(11) Data 7
+         (10)                      [+5v]---( 1) Vdd
+         (11)                      [GND]---( 2) Ground
+         (12)                      [+5v]---(14) Reset
+         (13)                      [GND]---(15) Read / Write
+    Line (14)------------------------------(13) Controller Select 1
+         (15)
+    Init (16)------------------------------(12) Controller Select 2
+  Select (17)------------------------------(16) Data / Instruction
+  Ground (18)---[GND]              [+5v]---(19) LED +
+  Ground (19)---[GND]
+  Ground (20)---[GND]              E    A             Values:
+  Ground (21)---[GND]       [GND]---[P1]---(18) Vee    - R = Resistor = 22 ohm
+  Ground (22)---[GND]                |                 - P1 = Preset = 10 Kohm
+  Ground (23)---[GND]       ----   S ------( 3) V0     - P2 = Preset = 1 Kohm
+  Ground (24)---[GND]       |  |
+  Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
+
+
+4. Userspace Programming
+------------------------
+
+The cfag12864bfb describes a framebuffer device (/dev/fbX).
+
+It has a size of 1024 bytes = 1 Kbyte.
+Each bit represents one pixel. If the bit is high, the pixel will
+turn on. If the pixel is low, the pixel will turn off.
+
+You can use the framebuffer as a file: fopen, fwrite, fclose...
+Although the LCD won't get updated until the next refresh time arrives.
+
+Also, you can mmap the framebuffer: open & mmap, munmap & close...
+which is the best option for most uses.
+
+Check samples/auxdisplay/cfag12864b-example.c
+for a real working userspace complete program with usage examples.
diff --git a/Documentation/admin-guide/auxdisplay/index.rst b/Documentation/admin-guide/auxdisplay/index.rst
new file mode 100644
index 000000000..31eae0825
--- /dev/null
+++ b/Documentation/admin-guide/auxdisplay/index.rst
@@ -0,0 +1,9 @@
+=========================
+Auxiliary Display Support
+=========================
+
+.. toctree::
+    :maxdepth: 1
+
+    ks0108.rst
+    cfag12864b.rst
diff --git a/Documentation/admin-guide/auxdisplay/ks0108.rst b/Documentation/admin-guide/auxdisplay/ks0108.rst
new file mode 100644
index 000000000..a7d3fe509
--- /dev/null
+++ b/Documentation/admin-guide/auxdisplay/ks0108.rst
@@ -0,0 +1,50 @@
+==========================================
+ks0108 LCD Controller Driver Documentation
+==========================================
+
+:License:		GPLv2
+:Author & Maintainer:	Miguel Ojeda <ojeda@kernel.org>
+:Date:			2006-10-27
+
+
+
+.. INDEX
+
+	1. DRIVER INFORMATION
+	2. DEVICE INFORMATION
+	3. WIRING
+
+
+1. Driver Information
+---------------------
+
+This driver supports the ks0108 LCD controller.
+
+
+2. Device Information
+---------------------
+
+:Manufacturer:	Samsung
+:Device Name:	KS0108 LCD Controller
+:Device Code:	ks0108
+:Webpage:	-
+:Device Webpage: -
+:Type:		LCD Controller (Liquid Crystal Display Controller)
+:Width:		64
+:Height:	64
+:Colors:	2 (B/N)
+:Pages:		8
+:Addresses:	64 each page
+:Data size:	1 byte each address
+:Memory size:	8 * 64 * 1 = 512 bytes
+
+
+3. Wiring
+---------
+
+The driver supports data parallel port wiring.
+
+If you aren't building LCD related hardware, you should check
+your LCD specific wiring information in the same folder.
+
+For example, check Documentation/admin-guide/auxdisplay/cfag12864b.rst