Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlgrafted

Pull pin control updates from Linus Walleij:
 "Core changes:

   - Use the non-blocking mux_state_try_select() in the generic MUX pin
     control back-end

   - Free pin maps on pinctrl_generic_to_map() failure in the core
     helpers

  New hardware pin control:

   - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC
     (this is for the low power audio, LPASS = Low Power Audio SubSystem
     portions)

   - Upboard support on top of the Intel pin controller

   - Apple T6030 and T6031 support (just compatible strings)

   - Samsung Exynos 8855 SoC

   - Mediatek MT6858 SoC

   - Rockchip RK3308B and RV1106 SoCs

   - Airoha EN7523 and AN7563 SoCs

  Improvements:

   - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable

   - Qualcomm improvements on top of the Qualcomm PDC (power domain
     controller) irqchip improvements from tglx:s tree

   - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups

   - The NPCM8xx driver has been put into shape fixing many pin and
     group definitions

   - Some non-urgent Tegra 264 pin assignments are fixed up

   - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and
     pin assignments, missing features etc"

* tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits)
  dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema
  pinctrl: meson: sync some modify from A4
  pinctrl: meson: a4: Add input enable pin configuration
  pinctrl: realtek: rtd1625: remove unused group name spdif_sel
  pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13
  dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema
  Revert "Merge branch 'ib-rsk7204' into devel"
  pinctrl: rockchip: Add RV1106 pinctrl support
  dt-bindings: pinctrl: rockchip: Add RV1106 compatible
  pinctrl: rockchip: Decode drive strength in the get function
  pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable
  pinctrl: airoha: add support of an7563 SoC
  dt-bindings: pinctrl: airoha: add support of an7563 pin controller
  pinctrl: airoha: try to find chip scu node by phandle first
  pinctrl: airoha: add support of en7523 SoC
  dt-bindings: pinctrl: airoha: add support of en7523 pin controller
  pinctrl: airoha: an7583: add support for olt pinmux
  pinctrl: airoha: an7583: add support for pon_alt pinmux
  pinctrl: airoha: an7583: add support for npu_uart pinmux
  dt-bindings: pinctrl: airoha: an7583: add missed features
  ...

1 files changed, 132 insertions, 0 deletions

diff --git a/Documentation/PCI/tph.rst b/Documentation/PCI/tph.rst
new file mode 100644
index 000000000..b6cf22b9b
--- /dev/null
+++ b/Documentation/PCI/tph.rst
@@ -0,0 +1,132 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+
+===========
+TPH Support
+===========
+
+:Copyright: 2024 Advanced Micro Devices, Inc.
+:Authors: - Eric van Tassell <eric.vantassell@amd.com>
+          - Wei Huang <wei.huang2@amd.com>
+
+
+Overview
+========
+
+TPH (TLP Processing Hints) is a PCIe feature that allows endpoint devices
+to provide optimization hints for requests that target memory space.
+These hints, in a format called Steering Tags (STs), are embedded in the
+requester's TLP headers, enabling the system hardware, such as the Root
+Complex, to better manage platform resources for these requests.
+
+For example, on platforms with TPH-based direct data cache injection
+support, an endpoint device can include appropriate STs in its DMA
+traffic to specify which cache the data should be written to. This allows
+the CPU core to have a higher probability of getting data from cache,
+potentially improving performance and reducing latency in data
+processing.
+
+
+How to Use TPH
+==============
+
+TPH is presented as an optional extended capability in PCIe. The Linux
+kernel handles TPH discovery during boot, but it is up to the device
+driver to request TPH enablement if it is to be utilized. Once enabled,
+the driver uses the provided API to obtain the Steering Tag for the
+target memory and to program the ST into the device's ST table.
+
+Enable TPH support in Linux
+---------------------------
+
+To support TPH, the kernel must be built with the CONFIG_PCIE_TPH option
+enabled.
+
+Manage TPH
+----------
+
+To enable TPH for a device, use the following function::
+
+  int pcie_enable_tph(struct pci_dev *pdev, int mode);
+
+This function enables TPH support for device with a specific ST mode.
+Current supported modes include:
+
+  * PCI_TPH_ST_NS_MODE - NO ST Mode
+  * PCI_TPH_ST_IV_MODE - Interrupt Vector Mode
+  * PCI_TPH_ST_DS_MODE - Device Specific Mode
+
+`pcie_enable_tph()` checks whether the requested mode is actually
+supported by the device before enabling. The device driver can figure out
+which TPH mode is supported and can be properly enabled based on the
+return value of `pcie_enable_tph()`.
+
+To disable TPH, use the following function::
+
+  void pcie_disable_tph(struct pci_dev *pdev);
+
+Manage ST
+---------
+
+Steering Tags are platform specific. PCIe spec does not specify where STs
+are from. Instead PCI Firmware Specification defines an ACPI _DSM method
+(see the `Revised _DSM for Cache Locality TPH Features ECN
+<https://members.pcisig.com/wg/PCI-SIG/document/15470>`_) for retrieving
+STs for a target memory of various properties. This method is what is
+supported in this implementation.
+
+To retrieve a Steering Tag for a target memory associated with a specific
+CPU, use the following function::
+
+  int pcie_tph_get_cpu_st(struct pci_dev *pdev, enum tph_mem_type type,
+                          unsigned int cpu, u16 *tag);
+
+The `type` argument is used to specify the memory type, either volatile
+or persistent, of the target memory. The `cpu` argument specifies the
+CPU where the memory is associated to.
+
+After the ST value is retrieved, the device driver can use the following
+function to write the ST into the device::
+
+  int pcie_tph_set_st_entry(struct pci_dev *pdev, unsigned int index,
+                            u16 tag);
+
+The `index` argument is the ST table entry index the ST tag will be
+written into. `pcie_tph_set_st_entry()` will figure out the proper
+location of ST table, either in the MSI-X table or in the TPH Extended
+Capability space, and write the Steering Tag into the ST entry pointed by
+the `index` argument.
+
+It is completely up to the driver to decide how to use these TPH
+functions. For example a network device driver can use the TPH APIs above
+to update the Steering Tag when interrupt affinity of a RX/TX queue has
+been changed. Here is a sample code for IRQ affinity notifier:
+
+.. code-block:: c
+
+    static void irq_affinity_notified(struct irq_affinity_notify *notify,
+                                      const cpumask_t *mask)
+    {
+         struct drv_irq *irq;
+         unsigned int cpu_id;
+         u16 tag;
+
+         irq = container_of(notify, struct drv_irq, affinity_notify);
+         cpumask_copy(irq->cpu_mask, mask);
+
+         /* Pick a right CPU as the target - here is just an example */
+         cpu_id = cpumask_first(irq->cpu_mask);
+
+         if (pcie_tph_get_cpu_st(irq->pdev, TPH_MEM_TYPE_VM, cpu_id,
+                                 &tag))
+             return;
+
+         if (pcie_tph_set_st_entry(irq->pdev, irq->msix_nr, tag))
+             return;
+    }
+
+Disable TPH system-wide
+-----------------------
+
+There is a kernel command line option available to control TPH feature:
+    * "notph": TPH will be disabled for all endpoint devices.