openrisc: fix arbitrary kernel memory access via or1k_atomic syscallgrafted

sys_or1k_atomic() (syscall 244 in the "or1k" ABI) takes two user
pointers, v1 and v2, and swaps the words they point to in hand-written
assembly.

    l.lwz   r29,0(r4)
    l.lwz   r27,0(r5)
    l.sw    0(r4),r27
    l.sw    0(r5),r29

The pointers are not checked with access_ok(). The four memory
accesses also have no exception table entries.

A caller passes a kernel address as either pointer, and the syscall
reads from and writes to it directly.

This gives an unprivileged process a kernel read/write primitive. It
overwrites kernel data such as the sys_call_table, gaining code
execution in kernel context.

Check both pointers before entering the critical section. Add fixups
for the four memory accesses so faults on valid but unmapped user
addresses return -EFAULT.

[shorne@gmail.com: fix comment style]
Fixes: 9d02a4283e9c ("OpenRISC: Boot code")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>

1 files changed, 62 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-tty b/Documentation/ABI/testing/sysfs-class-led-trigger-tty
new file mode 100644
index 000000000..308fbc362
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-class-led-trigger-tty
@@ -0,0 +1,62 @@
+What:		/sys/class/leds/<tty_led>/ttyname
+Date:		Dec 2020
+KernelVersion:	5.10
+Contact:	linux-leds@vger.kernel.org
+Description:
+		Specifies the tty device name of the triggering tty
+
+What:		/sys/class/leds/<tty_led>/rx
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		Signal reception (rx) of data on the named tty device.
+		If set to 0, the LED will not blink on reception.
+		If set to 1 (default), the LED will blink on reception.
+
+What:		/sys/class/leds/<tty_led>/tx
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		Signal transmission (tx) of data on the named tty device.
+		If set to 0, the LED will not blink on transmission.
+		If set to 1 (default), the LED will blink on transmission.
+
+What:		/sys/class/leds/<tty_led>/cts
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		CTS = Clear To Send
+		DCE is ready to accept data from the DTE.
+		If the line state is detected, the LED is switched on.
+		If set to 0 (default), the LED will not evaluate CTS.
+		If set to 1, the LED will evaluate CTS.
+
+What:		/sys/class/leds/<tty_led>/dsr
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		DSR = Data Set Ready
+		DCE is ready to receive and send data.
+		If the line state is detected, the LED is switched on.
+		If set to 0 (default), the LED will not evaluate DSR.
+		If set to 1, the LED will evaluate DSR.
+
+What:		/sys/class/leds/<tty_led>/dcd
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		DCD = Data Carrier Detect
+		DTE is receiving a carrier from the DCE.
+		If the line state is detected, the LED is switched on.
+		If set to 0 (default), the LED will not evaluate CAR (DCD).
+		If set to 1, the LED will evaluate CAR (DCD).
+
+What:		/sys/class/leds/<tty_led>/rng
+Date:		February 2024
+KernelVersion:	6.8
+Description:
+		RNG = Ring Indicator
+		DCE has detected an incoming ring signal on the telephone
+		line. If the line state is detected, the LED is switched on.
+		If set to 0 (default), the LED will not evaluate RNG.
+		If set to 1, the LED will evaluate RNG.