Merge tag 'i3c/for-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linuxgrafted

Pull I3C updates from Alexandre Belloni:
 "A new driver this cycle, for the AMD AXI I3C controller.

  There are also new features such as IBI wakeup support, SETAASA device
  discovery and ACPI support for the the DAA methods, meaning we can now
  communicate with the SPD devices on DDR5 modules.

  New driver:
   - AMD AXI I3C master controller

  Subsystem:
   - I3C Common Command Code (CCC) handling improvements, especially
     around GET CCCs
   - SETAASA device discovery support
   - ACPI support for all existing DAA methods like SETDASA, SETNEWDA as
     well as I2C devices on I3C bus
   - IBI-based wakeup support

  Drivers:
   - dw: SETAASA support
   - mipi-i3c-hci: advertise IBI wakeup capability, AMD_PT I3C
     controller support, PIO queue management support for HCI v1.2
   - renesas: improve suspend to RAM support, add runtime PM support"

* tag 'i3c/for-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (70 commits)
  i3c: dw: reduce do_daa time if there's no client
  i3c: mipi-i3c-hci: Add support for AMD_PT I3C controller
  i3c: mipi-i3c-hci: Add PIO queue management support for HCI v1.2
  i3c: mipi-i3c-hci: Fix missing STAT_IBI_STATUS_THLD in PIO mode
  i3c: dw: rename "pclk" to "apb" to match dt-binding
  i3c: dw: make struct dw_i3c_cmd smaller
  i3c: dw: use COMMAND_PORT_TRANSFER_ARG instead of hardcoding
  i3c: renesas: Don't register devices when ENTDAA times out
  i3c: master: dw-i3c-master: fix OD timing for first broadcast
  i3c: mipi-i3c-hci: Advertise IBI wakeup capability
  i3c: mipi-i3c-hci: Factor out i3c_hci_sysdev()
  i3c: mipi-i3c-hci-pci: Propagate I3C wakeup requirements to PCI
  i3c: master: Reject IBI requests from non-IBI-capable devices
  i3c: master: Add helper to query bus wakeup requirements
  i3c: master: Report wakeup events for IBIs
  i3c: master: Support IBI-based wakeup capability
  i3c: master: Fix potential UAF in i3c_device_match()
  i3c: master: Fix potential UAF in i3c_device_uevent()
  i3c: Make dev->desc locking assumptions explicit
  i3c: master: Fix use-after-free of master->this
  ...

1 files changed, 127 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc
new file mode 100644
index 000000000..27ed5919d
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-driver-dcc
@@ -0,0 +1,127 @@
+What:           /sys/kernel/debug/dcc/.../ready
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to check the status of the dcc
+		hardware if it's ready to receive user configurations.
+		A 'Y' here indicates dcc is ready.
+
+What:           /sys/kernel/debug/dcc/.../trigger
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This is the debugfs interface for manual software
+		triggers. The trigger can be invoked by writing '1'
+		to the file.
+
+What:           /sys/kernel/debug/dcc/.../config_reset
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This file is used to reset the configuration of
+		a dcc driver to the default configuration. When '1'
+		is written to the file, all the previous addresses
+		stored in the driver gets removed and users need to
+		reconfigure addresses again.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/config
+Date:		 December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This stores the addresses of the registers which
+		can be read in case of a hardware crash or manual
+		software triggers. The input addresses type
+		can be one of following dcc instructions: read,
+		write, read-write, and loop type. The lists need to
+		be configured sequentially and not in a overlapping
+		manner; e.g. users can jump to list x only after
+		list y is configured and enabled. The input format for
+		each type is as follows:
+
+	        i) Read instruction
+
+		   ::
+
+		     echo R <addr> <n> <bus> >/sys/kernel/debug/dcc/../[list-number]/config
+
+		   where:
+
+		   <addr>
+			The address to be read.
+
+		   <n>
+			The addresses word count, starting from address <1>.
+			Each word is 32 bits (4 bytes). If omitted, defaulted
+			to 1.
+
+		   <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+			The default is 'ahb' if leaved out.
+
+		ii) Write instruction
+
+		    ::
+
+		      echo W <addr> <n> <bus type> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <addr>
+			The address to be written.
+
+		    <n>
+			The value to be written at <addr>.
+
+		    <bus type>
+			The bus type, which can be either 'apb' or 'ahb'.
+
+	        iii) Read-write instruction
+
+		     ::
+
+		       echo RW <addr> <n> <mask> > /sys/kernel/debug/dcc/../[list-number]/config
+
+		     where:
+
+		     <addr>
+			The address to be read and written.
+
+		     <n>
+		        The value to be written at <addr>.
+
+		     <mask>
+			The value mask.
+
+		iv) Loop instruction
+
+		    ::
+
+		      echo L <loop count> <address count> <address>... > /sys/kernel/debug/dcc/../[list-number]/config
+
+		    where:
+
+		    <loop count>
+			Number of iterations
+
+		    <address count>
+			total number of addresses to be written
+
+		    <address>
+			Space-separated list of addresses.
+
+What:           /sys/kernel/debug/dcc/.../[list-number]/enable
+Date:           December 2022
+Contact:        Souradeep Chowdhury <quic_schowdhu@quicinc.com>
+Description:
+		This debugfs interface is used for enabling the
+		the dcc hardware. A file named "enable" is in the
+		directory list number where users can enable/disable
+		the specific list by writing boolean (1 or 0) to the
+		file.
+
+		On enabling the dcc, all the addresses specified
+		by the user for the corresponding list is written
+		into dcc sram which is read by the dcc hardware
+		on manual or crash induced triggers. Lists must
+		be configured and enabled sequentially, e.g. list
+		2 can only be enabled when list 1 have so.