From 33a154a96e71a34a1bcca9f40da343dbbf7b38b4 Mon Sep 17 00:00:00 2001 From: Alexei Starovoitov Date: Thu, 1 Oct 2026 14:52:55 +0000 Subject: selftests/bpf: Test packet range of pointers sharing an id Add tests where two packet pointers share an id and tightening one pointer's umax from its var_off would put it less than their constant distance from the other's umax: with an index & 0x38 capped at 50, the base pointer keeps umax 50, so the pointer 8 bytes further on must keep umax 58, even though its known bits allow at most 56. These refused a valid program or accepted an out-of-bounds access before the fix: - check the advanced copy, load through the base: valid, was refused; - check the base, load the byte at base + 1 through a copy advanced by 8: was accepted; - check base + 4, load 4 bytes at base + 2 through base + 8: reads two bytes past the checked range, was accepted; - the same as the second with data_meta pointers checked against data: was accepted. These pass with and without the fix and cover nearby paths: - subtract an unknown scalar from a checked pointer and load below it (the range is kept across a new id); - reach a load through two paths whose checks cover 8 and 7 bytes after the loaded pointer; the second path must not be pruned by the first; - spill a copy of a pointer, check the pointer, fill the copy and load one byte past the checked range: the load is refused, and the copy has the range of the check. Signed-off-by: Alexei Starovoitov Link: https://lore.kernel.org/bpf/20261001145255.855630-2-alexei.starovoitov@gmail.com Signed-off-by: Kumar Kartikeya Dwivedi --- drivers/usb/serial/empeg.c | 122 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 122 insertions(+) create mode 100644 drivers/usb/serial/empeg.c (limited to 'drivers/usb/serial/empeg.c') diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c new file mode 100644 index 000000000..4937575ca --- /dev/null +++ b/drivers/usb/serial/empeg.c @@ -0,0 +1,122 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * USB Empeg empeg-car player driver + * + * Copyright (C) 2000, 2001 + * Gary Brubaker (xavyer@ix.netcom.com) + * + * Copyright (C) 1999 - 2001 + * Greg Kroah-Hartman (greg@kroah.com) + * + * See Documentation/usb/usb-serial.rst for more information on using this + * driver + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_AUTHOR "Greg Kroah-Hartman , Gary Brubaker " +#define DRIVER_DESC "USB Empeg Mark I/II Driver" + +#define EMPEG_VENDOR_ID 0x084f +#define EMPEG_PRODUCT_ID 0x0001 + +/* function prototypes for an empeg-car player */ +static int empeg_startup(struct usb_serial *serial); +static void empeg_init_termios(struct tty_struct *tty); + +static const struct usb_device_id id_table[] = { + { USB_DEVICE(EMPEG_VENDOR_ID, EMPEG_PRODUCT_ID) }, + { } /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(usb, id_table); + +static struct usb_serial_driver empeg_device = { + .driver = { + .name = "empeg", + }, + .id_table = id_table, + .num_ports = 1, + .bulk_out_size = 256, + .throttle = usb_serial_generic_throttle, + .unthrottle = usb_serial_generic_unthrottle, + .attach = empeg_startup, + .init_termios = empeg_init_termios, +}; + +static struct usb_serial_driver * const serial_drivers[] = { + &empeg_device, NULL +}; + +static int empeg_startup(struct usb_serial *serial) +{ + int r; + + if (serial->dev->actconfig->desc.bConfigurationValue != 1) { + dev_err(&serial->dev->dev, "active config #%d != 1 ??\n", + serial->dev->actconfig->desc.bConfigurationValue); + return -ENODEV; + } + + r = usb_reset_configuration(serial->dev); + + /* continue on with initialization */ + return r; +} + +static void empeg_init_termios(struct tty_struct *tty) +{ + struct ktermios *termios = &tty->termios; + + /* + * The empeg-car player wants these particular tty settings. + * You could, for example, change the baud rate, however the + * player only supports 115200 (currently), so there is really + * no point in support for changes to the tty settings. + * (at least for now) + * + * The default requirements for this device are: + */ + termios->c_iflag + &= ~(IGNBRK /* disable ignore break */ + | BRKINT /* disable break causes interrupt */ + | PARMRK /* disable mark parity errors */ + | ISTRIP /* disable clear high bit of input characters */ + | INLCR /* disable translate NL to CR */ + | IGNCR /* disable ignore CR */ + | ICRNL /* disable translate CR to NL */ + | IXON); /* disable enable XON/XOFF flow control */ + + termios->c_oflag + &= ~OPOST; /* disable postprocess output characters */ + + termios->c_lflag + &= ~(ECHO /* disable echo input characters */ + | ECHONL /* disable echo new line */ + | ICANON /* disable erase, kill, werase, and rprnt special characters */ + | ISIG /* disable interrupt, quit, and suspend special characters */ + | IEXTEN); /* disable non-POSIX special characters */ + + termios->c_cflag + &= ~(CSIZE /* no size */ + | PARENB /* disable parity bit */ + | CBAUD); /* clear current baud rate */ + + termios->c_cflag + |= CS8; /* character size 8 bits */ + + tty_encode_baud_rate(tty, 115200, 115200); +} + +module_usb_serial_driver(serial_drivers, id_table); + +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL v2"); -- cgit v1.3.1