From 2bc6b218717b9d08f466f88209251d54bc09b207 Mon Sep 17 00:00:00 2001 From: Fuad Tabba Date: Tue, 22 Sep 2026 19:14:30 +0100 Subject: arm64/boot: Disable trapping of PMZR_EL0 writes to EL2 __init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2. PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a write from EL0 reaches the trap and takes the host down without a panic message. Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9 bits. Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9") Cc: stable@vger.kernel.org Signed-off-by: Fuad Tabba Reviewed-by: Anshuman Khandual Reviewed-by: Oliver Upton Signed-off-by: Will Deacon --- drivers/phy/starfive/Kconfig | 48 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) create mode 100644 drivers/phy/starfive/Kconfig (limited to 'drivers/phy/starfive/Kconfig') diff --git a/drivers/phy/starfive/Kconfig b/drivers/phy/starfive/Kconfig new file mode 100644 index 000000000..d0cdd7cb4 --- /dev/null +++ b/drivers/phy/starfive/Kconfig @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Phy drivers for StarFive platforms +# + +if ARCH_STARFIVE || COMPILE_TEST + +config PHY_STARFIVE_JH7110_DPHY_RX + tristate "StarFive JH7110 D-PHY RX support" + depends on HAS_IOMEM + select GENERIC_PHY + select GENERIC_PHY_MIPI_DPHY + help + Choose this option if you have a StarFive D-PHY in your + system. If M is selected, the module will be called + phy-jh7110-dphy-rx.ko. + +config PHY_STARFIVE_JH7110_DPHY_TX + tristate "StarFive JH7110 D-PHY TX Support" + depends on HAS_IOMEM + select GENERIC_PHY + select GENERIC_PHY_MIPI_DPHY + help + Choose this option if you have a StarFive D-PHY TX in your + system. If M is selected, the module will be called + phy-jh7110-dphy-tx.ko. + +config PHY_STARFIVE_JH7110_PCIE + tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support" + depends on HAS_IOMEM + select GENERIC_PHY + help + Enable this to support the StarFive PCIe 2.0 PHY, + or used as USB 3.0 PHY. + If M is selected, the module will be called + phy-jh7110-pcie.ko. + +config PHY_STARFIVE_JH7110_USB + tristate "Starfive JH7110 USB 2.0 PHY support" + depends on USB_SUPPORT + select GENERIC_PHY + help + Enable this to support the StarFive USB 2.0 PHY, + used with the Cadence USB controller. + If M is selected, the module will be called + phy-jh7110-usb.ko. + +endif # ARCH_STARFIVE || COMPILE_TEST -- cgit v1.3.1