From 2bc6b218717b9d08f466f88209251d54bc09b207 Mon Sep 17 00:00:00 2001 From: Fuad Tabba Date: Tue, 22 Sep 2026 19:14:30 +0100 Subject: arm64/boot: Disable trapping of PMZR_EL0 writes to EL2 __init_el2_fgt2() writes one mask to both HDFGRTR2_EL2 and HDFGWTR2_EL2. PMZR_EL0 is write-only, so its trap bit, nPMZR_EL0, exists only in HDFGWTR2_EL2 and is therefore never set: a PMZR_EL0 write from the host traps to EL2, where the nVHE hypervisor has no handler and BUG()s. The kernel never writes PMZR_EL0, but kernel.perf_user_access=1 has the PMU driver set PMUSERENR_EL0.UEN for a task with a user-read event, so a write from EL0 reaches the trap and takes the host down without a panic message. Accumulate the HDFGWTR2_EL2 bits separately, as __init_el2_fgt() already does for HDFGWTR_EL2, and set nPMZR_EL0 with the other FEAT_PMUv3p9 bits. Fixes: 858c7bfcb35e1 ("arm64/boot: Enable EL2 requirements for FEAT_PMUv3p9") Cc: stable@vger.kernel.org Signed-off-by: Fuad Tabba Reviewed-by: Anshuman Khandual Reviewed-by: Oliver Upton Signed-off-by: Will Deacon --- drivers/phy/st/Kconfig | 60 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 drivers/phy/st/Kconfig (limited to 'drivers/phy/st/Kconfig') diff --git a/drivers/phy/st/Kconfig b/drivers/phy/st/Kconfig new file mode 100644 index 000000000..49206185e --- /dev/null +++ b/drivers/phy/st/Kconfig @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Phy drivers for STMicro platforms +# +config PHY_MIPHY28LP + tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407" + depends on ARCH_STI || COMPILE_TEST + select GENERIC_PHY + help + Enable this to support the miphy transceiver (for SATA/PCIE/USB3) + that is part of STMicroelectronics STiH407 SoC. + +config PHY_ST_SPEAR1310_MIPHY + tristate "ST SPEAR1310-MIPHY driver" + select GENERIC_PHY + depends on MACH_SPEAR1310 || COMPILE_TEST + help + Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA. + +config PHY_ST_SPEAR1340_MIPHY + tristate "ST SPEAR1340-MIPHY driver" + select GENERIC_PHY + depends on MACH_SPEAR1340 || COMPILE_TEST + help + Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA. + +config PHY_STIH407_USB + tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family" + depends on RESET_CONTROLLER + depends on ARCH_STI || COMPILE_TEST + select GENERIC_PHY + help + Enable this support to enable the picoPHY device used by USB2 + and USB3 controllers on STMicroelectronics STiH407 SoC families. + +config PHY_STM32_COMBOPHY + tristate "STMicroelectronics COMBOPHY driver for STM32MP25" + depends on ARCH_STM32 || COMPILE_TEST + select GENERIC_PHY + help + Enable this to support the COMBOPHY device used by USB3 or PCIe + controllers on STMicroelectronics STM32MP25 SoC. + This driver controls the COMBOPHY block to generate the PCIe 100Mhz + reference clock from either the external clock generator or HSE + internal SoC clock source. + +config PHY_STM32_USBPHYC + tristate "STMicroelectronics STM32 USB HS PHY Controller driver" + depends on ARCH_STM32 || COMPILE_TEST + depends on COMMON_CLK + select GENERIC_PHY + help + Enable this to support the High-Speed USB transceivers that are part + of some STMicroelectronics STM32 SoCs. + + This driver controls the entire USB PHY block: the USB PHY controller + (USBPHYC) and the two 8-bit wide UTMI+ interfaces. First interface is + used by an HS USB Host controller, and the second one is shared + between an HS USB OTG controller and an HS USB Host controller, + selected by a USB switch. -- cgit v1.3.1