From cf9610f9116d55c5a66ef9f1faecacabd93a9322 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 24 Aug 2026 08:46:03 -0700 Subject: Merge tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "Core changes: - Use the non-blocking mux_state_try_select() in the generic MUX pin control back-end - Free pin maps on pinctrl_generic_to_map() failure in the core helpers New hardware pin control: - Qualcomm Maili TLMM SoC, PMG1110 PMIC, and Eliza LPASS LPI TLMM SoC (this is for the low power audio, LPASS = Low Power Audio SubSystem portions) - Upboard support on top of the Intel pin controller - Apple T6030 and T6031 support (just compatible strings) - Samsung Exynos 8855 SoC - Mediatek MT6858 SoC - Rockchip RK3308B and RV1106 SoCs - Airoha EN7523 and AN7563 SoCs Improvements: - Qualcomm TLMM GPIOs are unconditionally marked as wakeup capable - Qualcomm improvements on top of the Qualcomm PDC (power domain controller) irqchip improvements from tglx:s tree - Qualcomm IPQ806x and IPQ9650 non-urgent pin grop fixups - The NPCM8xx driver has been put into shape fixing many pin and group definitions - Some non-urgent Tegra 264 pin assignments are fixed up - Some non-urgent fixups to Airoha AN7581 and AN7583 registers and pin assignments, missing features etc" * tag 'pinctrl-v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (130 commits) dt-bindings: pinctrl: Convert TI DA850 pupd to DT schema pinctrl: meson: sync some modify from A4 pinctrl: meson: a4: Add input enable pin configuration pinctrl: realtek: rtd1625: remove unused group name spdif_sel pinctrl: realtek: rtd1625: fix base_bit for VE4 GPIO 13 dt-bindings: pinctrl: microchip,pic32mzda-pinctrl: Convert to DT schema Revert "Merge branch 'ib-rsk7204' into devel" pinctrl: rockchip: Add RV1106 pinctrl support dt-bindings: pinctrl: rockchip: Add RV1106 compatible pinctrl: rockchip: Decode drive strength in the get function pinctrl: fix PINCTRL_GENERIC_MUX not always being selectable pinctrl: airoha: add support of an7563 SoC dt-bindings: pinctrl: airoha: add support of an7563 pin controller pinctrl: airoha: try to find chip scu node by phandle first pinctrl: airoha: add support of en7523 SoC dt-bindings: pinctrl: airoha: add support of en7523 pin controller pinctrl: airoha: an7583: add support for olt pinmux pinctrl: airoha: an7583: add support for pon_alt pinmux pinctrl: airoha: an7583: add support for npu_uart pinmux dt-bindings: pinctrl: airoha: an7583: add missed features ... --- Documentation/driver-api/hsi.rst | 88 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 Documentation/driver-api/hsi.rst (limited to 'Documentation/driver-api/hsi.rst') diff --git a/Documentation/driver-api/hsi.rst b/Documentation/driver-api/hsi.rst new file mode 100644 index 000000000..01b6bebfb --- /dev/null +++ b/Documentation/driver-api/hsi.rst @@ -0,0 +1,88 @@ +High Speed Synchronous Serial Interface (HSI) +============================================= + +Introduction +--------------- + +High Speed Synchronous Interface (HSI) is a full duplex, low latency protocol, +that is optimized for die-level interconnect between an Application Processor +and a Baseband chipset. It has been specified by the MIPI alliance in 2003 and +implemented by multiple vendors since then. + +The HSI interface supports full duplex communication over multiple channels +(typically 8) and is capable of reaching speeds up to 200 Mbit/s. + +The serial protocol uses two signals, DATA and FLAG as combined data and clock +signals and an additional READY signal for flow control. An additional WAKE +signal can be used to wakeup the chips from standby modes. The signals are +commonly prefixed by AC for signals going from the application die to the +cellular die and CA for signals going the other way around. + +:: + + +------------+ +---------------+ + | Cellular | | Application | + | Die | | Die | + | | - - - - - - CAWAKE - - - - - - >| | + | T|------------ CADATA ------------>|R | + | X|------------ CAFLAG ------------>|X | + | |<----------- ACREADY ------------| | + | | | | + | | | | + | |< - - - - - ACWAKE - - - - - - -| | + | R|<----------- ACDATA -------------|T | + | X|<----------- ACFLAG -------------|X | + | |------------ CAREADY ----------->| | + | | | | + | | | | + +------------+ +---------------+ + +HSI Subsystem in Linux +------------------------- + +In the Linux kernel the hsi subsystem is supposed to be used for HSI devices. +The hsi subsystem contains drivers for hsi controllers including support for +multi-port controllers and provides a generic API for using the HSI ports. + +It also contains HSI client drivers, which make use of the generic API to +implement a protocol used on the HSI interface. These client drivers can +use an arbitrary number of channels. + +hsi-char Device +------------------ + +Each port automatically registers a generic client driver called hsi_char, +which provides a character device for userspace representing the HSI port. +It can be used to communicate via HSI from userspace. Userspace may +configure the hsi_char device using the following ioctl commands: + +HSC_RESET + flush the HSI port + +HSC_SET_PM + enable or disable the client. + +HSC_SEND_BREAK + send break + +HSC_SET_RX + set RX configuration + +HSC_GET_RX + get RX configuration + +HSC_SET_TX + set TX configuration + +HSC_GET_TX + get TX configuration + +The kernel HSI API +------------------ + +.. kernel-doc:: include/linux/hsi/hsi.h + :internal: + +.. kernel-doc:: drivers/hsi/hsi_core.c + :export: + -- cgit v1.3.1