From 106b4a2a78b2a2f14885604891957b84bba502db Mon Sep 17 00:00:00 2001 From: Adrian Betschart Date: Fri, 11 Sep 2026 17:13:14 +0200 Subject: drm/amd/display: Try RGB before YCbCr 4:4:4 in stream validation amdgpu_dm_create_validate_stream_for_sink() walks encoding_order[] and uses the first encoding that validates. YCbCr 4:4:4 is listed before RGB, so an HDMI sink that advertises 4:4:4 gets YCbCr 4:4:4 whenever the "color format" property is left at AUTO, even though RGB fits the same link. That contradicts the documented AUTO behaviour for HDMI in enum drm_connector_color_format (RGB, falling back to YCbCr 4:2:0 only when the bandwidth is not available or the mode is 4:2:0-only), which the amdgpu implementation of the property also describes. It also leaves the "Broadcast RGB" property without effect on such sinks, since the quantization range it selects only applies to RGB output. Try RGB first. The mask still holds every encoding the sink supports, so a mode that cannot carry RGB falls back exactly as before. For reference, v7.2 picked RGB here unless YCbCr 4:4:4 was forced through debugfs, while earlier kernels picked YCbCr 4:4:4 for any HDMI sink that advertised it. Fixes: 0b0ff65d3ca1 ("drm/amd/display: Refactor stream validation") Suggested-by: Adolfo Rodrigues Assisted-by: Claude Code:claude-fable-5-1 Signed-off-by: Adrian Betschart Reviewed-by: Fangzhi Zuo Tested-by: Adolfo Rodrigues Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher (cherry picked from commit 7de432bc753133764dc40d37f9388da56de251e7) --- Documentation/devicetree/changesets.rst | 37 +++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 Documentation/devicetree/changesets.rst (limited to 'Documentation/devicetree/changesets.rst') diff --git a/Documentation/devicetree/changesets.rst b/Documentation/devicetree/changesets.rst new file mode 100644 index 000000000..2091468d4 --- /dev/null +++ b/Documentation/devicetree/changesets.rst @@ -0,0 +1,37 @@ +.. SPDX-License-Identifier: GPL-2.0 + +===================== +Devicetree Changesets +===================== + +A Devicetree changeset is a method which allows one to apply changes +in the live tree in such a way that either the full set of changes +will be applied, or none of them will be. If an error occurs partway +through applying the changeset, then the tree will be rolled back to the +previous state. A changeset can also be removed after it has been +applied. + +When a changeset is applied, all of the changes get applied to the tree +at once before emitting OF_RECONFIG notifiers. This is so that the +receiver sees a complete and consistent state of the tree when it +receives the notifier. + +The sequence of a changeset is as follows. + +1. of_changeset_init() - initializes a changeset + +2. A number of DT tree change calls, of_changeset_attach_node(), + of_changeset_detach_node(), of_changeset_add_property(), + of_changeset_remove_property, of_changeset_update_property() to prepare + a set of changes. No changes to the active tree are made at this point. + All the change operations are recorded in the of_changeset 'entries' + list. + +3. of_changeset_apply() - Apply the changes to the tree. Either the + entire changeset will get applied, or if there is an error the tree will + be restored to the previous state. The core ensures proper serialization + through locking. An unlocked version __of_changeset_apply is available, + if needed. + +If a successfully applied changeset needs to be removed, it can be done +with of_changeset_revert(). -- cgit v1.3.1