From e24328974a88aa8541e94e8bb8dfa2ade1b3c45d Mon Sep 17 00:00:00 2001 From: Donggeun Yoo Date: Wed, 2 Sep 2026 00:21:26 +0900 Subject: iio: proximity: vl53l0x-i2c: claim direct mode for raw reads vl53l0x_read_raw() starts a single-shot ranging measurement and reads back the result. Once the triggered buffer is enabled the sensor runs in continuous mode and its data-ready interrupt is routed to the trigger, so a concurrent in_distance_raw read disturbs the streaming setup and never gets its completion, returning -ETIMEDOUT. The original submission claimed direct mode here, but it was dropped during review because the driver had no buffer support at the time [1]. Continuous (buffered) mode was later added without restoring the claim [2], reintroducing the conflict. Reject direct reads while buffered capture is active by claiming direct mode around the measurement, as the vl53l1x sibling already does. Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support") Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1] Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2] Signed-off-by: Donggeun Yoo Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- Documentation/block/error-injection.rst | 59 +++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+) create mode 100644 Documentation/block/error-injection.rst (limited to 'Documentation/block/error-injection.rst') diff --git a/Documentation/block/error-injection.rst b/Documentation/block/error-injection.rst new file mode 100644 index 000000000..81f31af82 --- /dev/null +++ b/Documentation/block/error-injection.rst @@ -0,0 +1,59 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================ +Configurable Error Injection +============================ + +Overview +-------- + +Configurable error injection allows injecting specific block layer status codes +for sector ranges of a block device. Errors can be injected unconditionally, or +with a given probability. + +To use configurable error injection, CONFIG_BLK_ERROR_INJECTION must be enabled. + +The only interface is the error_injection debugfs file, which is created for +each registered gendisk. Writes to this file are used to create or delete rules +and reads return a list of the current error injection sites. + +Options +------- + +The following options specify the operations: + +=================== ======================================================= +add add a new rule +removeall remove all existing rules +=================== ======================================================= + +The following options specify the details of the rule for the add operation: + +=================== ======================================================= +op= block layer operation this rule applies to. This uses + the XYZ for each REQ_OP_XYZ operation, e.g. READ, WRITE + or DISCARD. Mandatory. +status= Status to return. This uses XYZ for each BLK_STS_XYZ + code, e.g. IOERR or MEDIUM. Mandatory. +start= First block layer sector the rule applies to. + Optional, defaults to 0. +nr_sectors= Number of sectors this rule applies. + Optional, defaults to the remainder of the device. +chance= Only return a failure with a likelihood of 1/chance. + Optional, defaults to 1 (always). +=================== ======================================================= + +Example +------- + +Return BLK_STS_IOERR for one in 10 reads of sector 0 of /dev/nvme0n1: + + $ echo 'add,op=READ,start=0,status=IOERR,chance=10' > /sys/kernel/debug/block/nvme0n1/error_injection + +Return BLK_STS_MEDIUM for every write to /dev/nvme0n1: + + $ echo 'add,op=WRITE,start=0,status=MEDIUM' > /sys/kernel/debug/block/nvme0n1/error_injection + +Remove all rules for /dev/nvme0n1: + + $ echo 'removeall' > /sys/kernel/debug/block/nvme0n1/error_injection -- cgit v1.3.1