From e24328974a88aa8541e94e8bb8dfa2ade1b3c45d Mon Sep 17 00:00:00 2001 From: Donggeun Yoo Date: Wed, 2 Sep 2026 00:21:26 +0900 Subject: iio: proximity: vl53l0x-i2c: claim direct mode for raw reads vl53l0x_read_raw() starts a single-shot ranging measurement and reads back the result. Once the triggered buffer is enabled the sensor runs in continuous mode and its data-ready interrupt is routed to the trigger, so a concurrent in_distance_raw read disturbs the streaming setup and never gets its completion, returning -ETIMEDOUT. The original submission claimed direct mode here, but it was dropped during review because the driver had no buffer support at the time [1]. Continuous (buffered) mode was later added without restoring the claim [2], reintroducing the conflict. Reject direct reads while buffered capture is active by claiming direct mode around the measurement, as the vl53l1x sibling already does. Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support") Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1] Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2] Signed-off-by: Donggeun Yoo Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- .../admin-guide/laptops/alienware-wmi.rst | 127 +++++++++++++++++++++ 1 file changed, 127 insertions(+) create mode 100644 Documentation/admin-guide/laptops/alienware-wmi.rst (limited to 'Documentation/admin-guide/laptops/alienware-wmi.rst') diff --git a/Documentation/admin-guide/laptops/alienware-wmi.rst b/Documentation/admin-guide/laptops/alienware-wmi.rst new file mode 100644 index 000000000..e532c60db --- /dev/null +++ b/Documentation/admin-guide/laptops/alienware-wmi.rst @@ -0,0 +1,127 @@ +.. SPDX-License-Identifier: GPL-2.0-or-later + +==================== +Alienware WMI Driver +==================== + +Kurt Borja + +This is a driver for the "WMAX" WMI device, which is found in most Dell gaming +laptops and controls various special features. + +Before the launch of M-Series laptops (~2018), the "WMAX" device controlled +basic RGB lighting, deep sleep mode, HDMI mode and amplifier status. + +Later, this device was completely repurpused. Now it mostly deals with thermal +profiles, sensor monitoring and overclocking. This interface is named "AWCC" and +is known to be used by the AWCC OEM application to control these features. + +The alienware-wmi driver controls both interfaces. + +AWCC Interface +============== + +WMI device documentation: Documentation/wmi/devices/alienware-wmi.rst + +Supported devices +----------------- + +- Alienware M-Series laptops +- Alienware X-Series laptops +- Alienware Aurora Desktops +- Dell G-Series laptops + +If you believe your device supports the AWCC interface and you don't have any of +the features described in this document, try the following alienware-wmi module +parameters: + +- ``force_platform_profile=1``: Forces probing for platform profile support +- ``force_hwmon=1``: Forces probing for HWMON support + +If the module loads successfully with these parameters, consider submitting a +patch adding your model to the ``awcc_dmi_table`` located in +``drivers/platform/x86/dell/alienware-wmi-wmax.c`` or contacting the maintainer +for further guidance. + +Status +------ + +The following features are currently supported: + +- :ref:`Platform Profile `: + + - Thermal profile control + + - G-Mode toggling + +- :ref:`HWMON `: + + - Sensor monitoring + + - Manual fan control + +.. _platform-profile: + +Platform Profile +---------------- + +The AWCC interface exposes various firmware defined thermal profiles. These are +exposed to user-space through the Platform Profile class interface. Refer to +:ref:`sysfs-class-platform-profile ` +for more information. + +The name of the platform-profile class device exported by this driver is +"alienware-wmi" and it's path can be found with: + +:: + + grep -l "alienware-wmi" /sys/class/platform-profile/platform-profile-*/name | sed 's|/[^/]*$||' + +If the device supports G-Mode, it is also toggled when selecting the +``performance`` profile. + +.. note:: + You may set the ``force_gmode`` module parameter to always try to toggle this + feature, without checking if your model supports it. + +.. _hwmon: + +HWMON +----- + +The AWCC interface also supports sensor monitoring and manual fan control. Both +of these features are exposed to user-space through the HWMON interface. + +The name of the hwmon class device exported by this driver is "alienware_wmi" +and it's path can be found with: + +:: + + grep -l "alienware_wmi" /sys/class/hwmon/hwmon*/name | sed 's|/[^/]*$||' + +Sensor monitoring is done through the standard HWMON interface. Refer to +:ref:`sysfs-class-hwmon ` for more +information. + +Manual fan control on the other hand, is not exposed directly by the AWCC +interface. Instead it let's us control a fan `boost` value. This `boost` value +has the following approximate behavior over the fan pwm: + +:: + + pwm = pwm_base + (fan_boost / 255) * (pwm_max - pwm_base) + +Due to the above behavior, the fan `boost` control is exposed to user-space +through the following, custom hwmon sysfs attribute: + +=============================== ======= ======================================= +Name Perm Description +=============================== ======= ======================================= +fan[1-4]_boost RW Fan boost value. + + Integer value between 0 and 255 +=============================== ======= ======================================= + +.. note:: + In some devices, manual fan control only works reliably if the ``custom`` + platform profile is selected. -- cgit v1.3.1