From 0d6526f82c3cdefcca47f73f5fc08dc6f335eac6 Mon Sep 17 00:00:00 2001 From: Tim Chen Date: Mon, 21 Sep 2026 17:37:22 -0700 Subject: sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling bug alb_break_llc() decides whether to break LLC preference during active load balance. It does so by testing that every runnable fair task on the source rq prefers its LLC: env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable But the two counters cover different sets. nr_pref_llc_running is updated in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued, so it follows queued tasks. h_nr_runnable is updated in set_delayed()/ clear_delayed() and drops delay-dequeued tasks. So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks, alb_break_llc() returns false, and active balance is free to pull a task off its preferred LLC. Active balance only moves runnable tasks, and this is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB skips the per-task test in can_migrate_task(). The runnable set is the one we want. Fix it on the counter side. A task should be counted in nr_pref_llc_running exactly while it is both queued on its preferred LLC (pref_llc_queued) and runnable (!sched_delayed). Define that membership once in task_pref_llc_runnable(), and adjust the counter only through pref_llc_running_inc()/pref_llc_running_dec() from the four sites that change either input: account_llc_enqueue(), account_llc_dequeue(), set_delayed() and clear_delayed(). Gating every update on the same predicate keeps the delay, wake and dequeue paths from double-counting or underflowing; see the comments at those sites for the ordering. nr_llc_running and sd->llc_counts are not touched and stay on queued semantics. Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC") Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/ Reported-by: Zhan Xusheng Suggested-by: Chen Yu Signed-off-by: Tim Chen Signed-off-by: Peter Zijlstra (Intel) Signed-off-by: Ingo Molnar Reviewed-by: Kayra Cizmeci Cc: # v7.2.x Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com --- Documentation/admin-guide/init.rst | 48 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) create mode 100644 Documentation/admin-guide/init.rst (limited to 'Documentation/admin-guide/init.rst') diff --git a/Documentation/admin-guide/init.rst b/Documentation/admin-guide/init.rst new file mode 100644 index 000000000..41f06a091 --- /dev/null +++ b/Documentation/admin-guide/init.rst @@ -0,0 +1,48 @@ +Explaining the "No working init found." boot hang message +========================================================= +:Authors: Andreas Mohr + Cristian Souza + +This document provides some high-level reasons for failure +(listed roughly in order of execution) to load the init binary. + +1) **Unable to mount root FS**: Set "debug" kernel parameter (in bootloader + config file or CONFIG_CMDLINE) to get more detailed kernel messages. + +2) **init binary doesn't exist on rootfs**: Make sure you have the correct + root FS type (and ``root=`` kernel parameter points to the correct + partition), required drivers such as storage hardware (such as SCSI or + USB!) and filesystem (ext3, jffs2, etc.) are builtin (alternatively as + modules, to be pre-loaded by an initrd). + +3) **Broken console device**: Possibly a conflict in ``console= setup`` + --> initial console unavailable. E.g. some serial consoles are unreliable + due to serial IRQ issues (e.g. missing interrupt-based configuration). + Try using a different ``console= device`` or e.g. ``netconsole=``. + +4) **Binary exists but dependencies not available**: E.g. required library + dependencies of the init binary such as ``/lib/ld-linux.so.2`` missing or + broken. Use ``readelf -d |grep NEEDED`` to find out which libraries + are required. + +5) **Binary cannot be loaded**: Make sure the binary's architecture matches + your hardware. E.g. i386 vs. x86_64 mismatch, or trying to load x86 on ARM + hardware. In case you tried loading a non-binary file here (shell script?), + you should make sure that the script specifies an interpreter in its + shebang header line (``#!/...``) that is fully working (including its + library dependencies). And before tackling scripts, better first test a + simple non-script binary such as ``/bin/sh`` and confirm its successful + execution. To find out more, add code ``to init/main.c`` to display + kernel_execve()s return values. + +Please extend this explanation whenever you find new failure causes +(after all loading the init binary is a CRITICAL and hard transition step +which needs to be made as painless as possible), then submit a patch to LKML. +Further TODOs: + +- Implement the various ``run_init_process()`` invocations via a struct array + which can then store the ``kernel_execve()`` result value and on failure + log it all by iterating over **all** results (very important usability fix). +- Try to make the implementation itself more helpful in general, e.g. by + providing additional error messages at affected places. + -- cgit v1.3.1