From e24328974a88aa8541e94e8bb8dfa2ade1b3c45d Mon Sep 17 00:00:00 2001 From: Donggeun Yoo Date: Wed, 2 Sep 2026 00:21:26 +0900 Subject: iio: proximity: vl53l0x-i2c: claim direct mode for raw reads vl53l0x_read_raw() starts a single-shot ranging measurement and reads back the result. Once the triggered buffer is enabled the sensor runs in continuous mode and its data-ready interrupt is routed to the trigger, so a concurrent in_distance_raw read disturbs the streaming setup and never gets its completion, returning -ETIMEDOUT. The original submission claimed direct mode here, but it was dropped during review because the driver had no buffer support at the time [1]. Continuous (buffered) mode was later added without restoring the claim [2], reintroducing the conflict. Reject direct reads while buffered capture is active by claiming direct mode around the measurement, as the vl53l1x sibling already does. Fixes: 762186c6e7b1 ("iio: proximity: vl53l0x-i2c: Added continuous mode support") Link: https://lore.kernel.org/linux-iio/20180911160300.GA9212@himanshu-Vostro-3559/ [1] Link: https://lore.kernel.org/linux-iio/20240909101508.263085-3-abhashkumarjha123@gmail.com/ [2] Signed-off-by: Donggeun Yoo Cc: stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- .../admin-guide/device-mapper/dm-queue-length.rst | 48 ++++++++++++++++++++++ 1 file changed, 48 insertions(+) create mode 100644 Documentation/admin-guide/device-mapper/dm-queue-length.rst (limited to 'Documentation/admin-guide/device-mapper/dm-queue-length.rst') diff --git a/Documentation/admin-guide/device-mapper/dm-queue-length.rst b/Documentation/admin-guide/device-mapper/dm-queue-length.rst new file mode 100644 index 000000000..d8e381c1c --- /dev/null +++ b/Documentation/admin-guide/device-mapper/dm-queue-length.rst @@ -0,0 +1,48 @@ +=============== +dm-queue-length +=============== + +dm-queue-length is a path selector module for device-mapper targets, +which selects a path with the least number of in-flight I/Os. +The path selector name is 'queue-length'. + +Table parameters for each path: [] + +:: + + : The number of I/Os to dispatch using the selected + path before switching to the next path. + If not given, internal default is used. To check + the default value, see the activated table. + +Status for each path: + +:: + + : 'A' if the path is active, 'F' if the path is failed. + : The number of path failures. + : The number of in-flight I/Os on the path. + + +Algorithm +========= + +dm-queue-length increments/decrements 'in-flight' when an I/O is +dispatched/completed respectively. +dm-queue-length selects a path with the minimum 'in-flight'. + + +Examples +======== +In case that 2 paths (sda and sdb) are used with repeat_count == 128. + +:: + + # echo "0 10 multipath 0 0 1 1 queue-length 0 2 1 8:0 128 8:16 128" \ + dmsetup create test + # + # dmsetup table + test: 0 10 multipath 0 0 1 1 queue-length 0 2 1 8:0 128 8:16 128 + # + # dmsetup status + test: 0 10 multipath 2 0 0 0 1 1 E 0 2 1 8:0 A 0 0 8:16 A 0 0 -- cgit v1.3.1