From 0d6526f82c3cdefcca47f73f5fc08dc6f335eac6 Mon Sep 17 00:00:00 2001 From: Tim Chen Date: Mon, 21 Sep 2026 17:37:22 -0700 Subject: sched/cache: Keep nr_pref_llc_running in the runnable domain, to fix LLC mis-scheduling bug alb_break_llc() decides whether to break LLC preference during active load balance. It does so by testing that every runnable fair task on the source rq prefers its LLC: env->src_rq->nr_pref_llc_running == env->src_rq->cfs.h_nr_runnable But the two counters cover different sets. nr_pref_llc_running is updated in account_llc_enqueue()/account_llc_dequeue(), next to cfs_rq->nr_queued, so it follows queued tasks. h_nr_runnable is updated in set_delayed()/ clear_delayed() and drops delay-dequeued tasks. So under DELAY_DEQUEUE, a preferring task that goes to sleep stays counted in nr_pref_llc_running while h_nr_runnable falls. The equality then breaks, alb_break_llc() returns false, and active balance is free to pull a task off its preferred LLC. Active balance only moves runnable tasks, and this is the only LLC check it consults: once the stopper runs, LBF_ACTIVE_LB skips the per-task test in can_migrate_task(). The runnable set is the one we want. Fix it on the counter side. A task should be counted in nr_pref_llc_running exactly while it is both queued on its preferred LLC (pref_llc_queued) and runnable (!sched_delayed). Define that membership once in task_pref_llc_runnable(), and adjust the counter only through pref_llc_running_inc()/pref_llc_running_dec() from the four sites that change either input: account_llc_enqueue(), account_llc_dequeue(), set_delayed() and clear_delayed(). Gating every update on the same predicate keeps the delay, wake and dequeue paths from double-counting or underflowing; see the comments at those sites for the ordering. nr_llc_running and sd->llc_counts are not touched and stay on queued semantics. Fixes: 714059f79ff0 ("sched/cache: Handle moving single tasks to/from their preferred LLC") Closes: https://lore.kernel.org/lkml/20260827135000.735138-1-zhanxusheng@xiaomi.com/ Reported-by: Zhan Xusheng Suggested-by: Chen Yu Signed-off-by: Tim Chen Signed-off-by: Peter Zijlstra (Intel) Signed-off-by: Ingo Molnar Reviewed-by: Kayra Cizmeci Cc: # v7.2.x Link: https://patch.msgid.link/06af61afedac32e6477f57feb4d658f6c411c3af.1790035273.git.tim.c.chen@linux.intel.com --- .../admin-guide/auxdisplay/cfag12864b.rst | 98 ++++++++++++++++++++++ Documentation/admin-guide/auxdisplay/index.rst | 9 ++ Documentation/admin-guide/auxdisplay/ks0108.rst | 50 +++++++++++ 3 files changed, 157 insertions(+) create mode 100644 Documentation/admin-guide/auxdisplay/cfag12864b.rst create mode 100644 Documentation/admin-guide/auxdisplay/index.rst create mode 100644 Documentation/admin-guide/auxdisplay/ks0108.rst (limited to 'Documentation/admin-guide/auxdisplay') diff --git a/Documentation/admin-guide/auxdisplay/cfag12864b.rst b/Documentation/admin-guide/auxdisplay/cfag12864b.rst new file mode 100644 index 000000000..da385d851 --- /dev/null +++ b/Documentation/admin-guide/auxdisplay/cfag12864b.rst @@ -0,0 +1,98 @@ +=================================== +cfag12864b LCD Driver Documentation +=================================== + +:License: GPLv2 +:Author & Maintainer: Miguel Ojeda +:Date: 2006-10-27 + + + +.. INDEX + + 1. DRIVER INFORMATION + 2. DEVICE INFORMATION + 3. WIRING + 4. USERSPACE PROGRAMMING + +1. Driver Information +--------------------- + +This driver supports a cfag12864b LCD. + + +2. Device Information +--------------------- + +:Manufacturer: Crystalfontz +:Device Name: Crystalfontz 12864b LCD Series +:Device Code: cfag12864b +:Webpage: http://www.crystalfontz.com +:Device Webpage: http://www.crystalfontz.com/products/12864b/ +:Type: LCD (Liquid Crystal Display) +:Width: 128 +:Height: 64 +:Colors: 2 (B/N) +:Controller: ks0108 +:Controllers: 2 +:Pages: 8 each controller +:Addresses: 64 each page +:Data size: 1 byte each address +:Memory size: 2 * 8 * 64 * 1 = 1024 bytes = 1 Kbyte + + +3. Wiring +--------- + +The cfag12864b LCD Series don't have official wiring. + +The common wiring is done to the parallel port as shown:: + + Parallel Port cfag12864b + + Name Pin# Pin# Name + + Strobe ( 1)------------------------------(17) Enable + Data 0 ( 2)------------------------------( 4) Data 0 + Data 1 ( 3)------------------------------( 5) Data 1 + Data 2 ( 4)------------------------------( 6) Data 2 + Data 3 ( 5)------------------------------( 7) Data 3 + Data 4 ( 6)------------------------------( 8) Data 4 + Data 5 ( 7)------------------------------( 9) Data 5 + Data 6 ( 8)------------------------------(10) Data 6 + Data 7 ( 9)------------------------------(11) Data 7 + (10) [+5v]---( 1) Vdd + (11) [GND]---( 2) Ground + (12) [+5v]---(14) Reset + (13) [GND]---(15) Read / Write + Line (14)------------------------------(13) Controller Select 1 + (15) + Init (16)------------------------------(12) Controller Select 2 + Select (17)------------------------------(16) Data / Instruction + Ground (18)---[GND] [+5v]---(19) LED + + Ground (19)---[GND] + Ground (20)---[GND] E A Values: + Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm + Ground (22)---[GND] | - P1 = Preset = 10 Kohm + Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm + Ground (24)---[GND] | | + Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED - + + +4. Userspace Programming +------------------------ + +The cfag12864bfb describes a framebuffer device (/dev/fbX). + +It has a size of 1024 bytes = 1 Kbyte. +Each bit represents one pixel. If the bit is high, the pixel will +turn on. If the pixel is low, the pixel will turn off. + +You can use the framebuffer as a file: fopen, fwrite, fclose... +Although the LCD won't get updated until the next refresh time arrives. + +Also, you can mmap the framebuffer: open & mmap, munmap & close... +which is the best option for most uses. + +Check samples/auxdisplay/cfag12864b-example.c +for a real working userspace complete program with usage examples. diff --git a/Documentation/admin-guide/auxdisplay/index.rst b/Documentation/admin-guide/auxdisplay/index.rst new file mode 100644 index 000000000..31eae0825 --- /dev/null +++ b/Documentation/admin-guide/auxdisplay/index.rst @@ -0,0 +1,9 @@ +========================= +Auxiliary Display Support +========================= + +.. toctree:: + :maxdepth: 1 + + ks0108.rst + cfag12864b.rst diff --git a/Documentation/admin-guide/auxdisplay/ks0108.rst b/Documentation/admin-guide/auxdisplay/ks0108.rst new file mode 100644 index 000000000..a7d3fe509 --- /dev/null +++ b/Documentation/admin-guide/auxdisplay/ks0108.rst @@ -0,0 +1,50 @@ +========================================== +ks0108 LCD Controller Driver Documentation +========================================== + +:License: GPLv2 +:Author & Maintainer: Miguel Ojeda +:Date: 2006-10-27 + + + +.. INDEX + + 1. DRIVER INFORMATION + 2. DEVICE INFORMATION + 3. WIRING + + +1. Driver Information +--------------------- + +This driver supports the ks0108 LCD controller. + + +2. Device Information +--------------------- + +:Manufacturer: Samsung +:Device Name: KS0108 LCD Controller +:Device Code: ks0108 +:Webpage: - +:Device Webpage: - +:Type: LCD Controller (Liquid Crystal Display Controller) +:Width: 64 +:Height: 64 +:Colors: 2 (B/N) +:Pages: 8 +:Addresses: 64 each page +:Data size: 1 byte each address +:Memory size: 8 * 64 * 1 = 512 bytes + + +3. Wiring +--------- + +The driver supports data parallel port wiring. + +If you aren't building LCD related hardware, you should check +your LCD specific wiring information in the same folder. + +For example, check Documentation/admin-guide/auxdisplay/cfag12864b.rst -- cgit v1.3.1