From 33a154a96e71a34a1bcca9f40da343dbbf7b38b4 Mon Sep 17 00:00:00 2001 From: Alexei Starovoitov Date: Thu, 1 Oct 2026 14:52:55 +0000 Subject: selftests/bpf: Test packet range of pointers sharing an id Add tests where two packet pointers share an id and tightening one pointer's umax from its var_off would put it less than their constant distance from the other's umax: with an index & 0x38 capped at 50, the base pointer keeps umax 50, so the pointer 8 bytes further on must keep umax 58, even though its known bits allow at most 56. These refused a valid program or accepted an out-of-bounds access before the fix: - check the advanced copy, load through the base: valid, was refused; - check the base, load the byte at base + 1 through a copy advanced by 8: was accepted; - check base + 4, load 4 bytes at base + 2 through base + 8: reads two bytes past the checked range, was accepted; - the same as the second with data_meta pointers checked against data: was accepted. These pass with and without the fix and cover nearby paths: - subtract an unknown scalar from a checked pointer and load below it (the range is kept across a new id); - reach a load through two paths whose checks cover 8 and 7 bytes after the loaded pointer; the second path must not be pruned by the first; - spill a copy of a pointer, check the pointer, fill the copy and load one byte past the checked range: the load is refused, and the copy has the range of the check. Signed-off-by: Alexei Starovoitov Link: https://lore.kernel.org/bpf/20261001145255.855630-2-alexei.starovoitov@gmail.com Signed-off-by: Kumar Kartikeya Dwivedi --- Documentation/PCI/endpoint/pci-test-function.rst | 103 +++++++++++++++++++++++ 1 file changed, 103 insertions(+) create mode 100644 Documentation/PCI/endpoint/pci-test-function.rst (limited to 'Documentation/PCI/endpoint/pci-test-function.rst') diff --git a/Documentation/PCI/endpoint/pci-test-function.rst b/Documentation/PCI/endpoint/pci-test-function.rst new file mode 100644 index 000000000..3c8521d7a --- /dev/null +++ b/Documentation/PCI/endpoint/pci-test-function.rst @@ -0,0 +1,103 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================= +PCI Test Function +================= + +:Author: Kishon Vijay Abraham I + +Traditionally PCI RC has always been validated by using standard +PCI cards like ethernet PCI cards or USB PCI cards or SATA PCI cards. +However with the addition of EP-core in linux kernel, it is possible +to configure a PCI controller that can operate in EP mode to work as +a test device. + +The PCI endpoint test device is a virtual device (defined in software) +used to test the endpoint functionality and serve as a sample driver +for other PCI endpoint devices (to use the EP framework). + +The PCI endpoint test device has the following registers: + + 1) PCI_ENDPOINT_TEST_MAGIC + 2) PCI_ENDPOINT_TEST_COMMAND + 3) PCI_ENDPOINT_TEST_STATUS + 4) PCI_ENDPOINT_TEST_SRC_ADDR + 5) PCI_ENDPOINT_TEST_DST_ADDR + 6) PCI_ENDPOINT_TEST_SIZE + 7) PCI_ENDPOINT_TEST_CHECKSUM + 8) PCI_ENDPOINT_TEST_IRQ_TYPE + 9) PCI_ENDPOINT_TEST_IRQ_NUMBER + +* PCI_ENDPOINT_TEST_MAGIC + +This register will be used to test BAR0. A known pattern will be written +and read back from MAGIC register to verify BAR0. + +* PCI_ENDPOINT_TEST_COMMAND + +This register will be used by the host driver to indicate the function +that the endpoint device must perform. + +======== ================================================================ +Bitfield Description +======== ================================================================ +Bit 0 raise legacy IRQ +Bit 1 raise MSI IRQ +Bit 2 raise MSI-X IRQ +Bit 3 read command (read data from RC buffer) +Bit 4 write command (write data to RC buffer) +Bit 5 copy command (copy data from one RC buffer to another RC buffer) +======== ================================================================ + +* PCI_ENDPOINT_TEST_STATUS + +This register reflects the status of the PCI endpoint device. + +======== ============================== +Bitfield Description +======== ============================== +Bit 0 read success +Bit 1 read fail +Bit 2 write success +Bit 3 write fail +Bit 4 copy success +Bit 5 copy fail +Bit 6 IRQ raised +Bit 7 source address is invalid +Bit 8 destination address is invalid +======== ============================== + +* PCI_ENDPOINT_TEST_SRC_ADDR + +This register contains the source address (RC buffer address) for the +COPY/READ command. + +* PCI_ENDPOINT_TEST_DST_ADDR + +This register contains the destination address (RC buffer address) for +the COPY/WRITE command. + +* PCI_ENDPOINT_TEST_IRQ_TYPE + +This register contains the interrupt type (Legacy/MSI) triggered +for the READ/WRITE/COPY and raise IRQ (Legacy/MSI) commands. + +Possible types: + +====== == +Legacy 0 +MSI 1 +MSI-X 2 +====== == + +* PCI_ENDPOINT_TEST_IRQ_NUMBER + +This register contains the triggered ID interrupt. + +Admissible values: + +====== =========== +Legacy 0 +MSI [1 .. 32] +MSI-X [1 .. 2048] +====== =========== -- cgit v1.3.1