From 34ff636f322c6d5e4f0a52338fa63a7dff09a495 Mon Sep 17 00:00:00 2001 From: Joel Fernandes Date: Sat, 18 Jul 2026 13:15:36 -0400 Subject: scftorture: Count single_rpc offline failures in statistics output scf_torture_stats_print() aggregates each invoker thread's counters into a local scf_statistics structure before printing, but the n_single_rpc_ofl field is missing from the aggregation loop. As a result, the "single_rpc_ofl" value printed in the statistics line is always zero, even when smp_call_function_single() invocations for the RPC test have failed due to offline CPUs and been counted by the invoker threads. Add the missing accumulation so that the printed value reflects the actual counts. Signed-off-by: Joel Fernandes Signed-off-by: Paul E. McKenney --- Documentation/ABI/testing/debugfs-driver-dcc | 127 +++++++++++++++++++++++++++ 1 file changed, 127 insertions(+) create mode 100644 Documentation/ABI/testing/debugfs-driver-dcc (limited to 'Documentation/ABI/testing/debugfs-driver-dcc') diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc new file mode 100644 index 000000000..27ed5919d --- /dev/null +++ b/Documentation/ABI/testing/debugfs-driver-dcc @@ -0,0 +1,127 @@ +What: /sys/kernel/debug/dcc/.../ready +Date: December 2022 +Contact: Souradeep Chowdhury +Description: + This file is used to check the status of the dcc + hardware if it's ready to receive user configurations. + A 'Y' here indicates dcc is ready. + +What: /sys/kernel/debug/dcc/.../trigger +Date: December 2022 +Contact: Souradeep Chowdhury +Description: + This is the debugfs interface for manual software + triggers. The trigger can be invoked by writing '1' + to the file. + +What: /sys/kernel/debug/dcc/.../config_reset +Date: December 2022 +Contact: Souradeep Chowdhury +Description: + This file is used to reset the configuration of + a dcc driver to the default configuration. When '1' + is written to the file, all the previous addresses + stored in the driver gets removed and users need to + reconfigure addresses again. + +What: /sys/kernel/debug/dcc/.../[list-number]/config +Date: December 2022 +Contact: Souradeep Chowdhury +Description: + This stores the addresses of the registers which + can be read in case of a hardware crash or manual + software triggers. The input addresses type + can be one of following dcc instructions: read, + write, read-write, and loop type. The lists need to + be configured sequentially and not in a overlapping + manner; e.g. users can jump to list x only after + list y is configured and enabled. The input format for + each type is as follows: + + i) Read instruction + + :: + + echo R >/sys/kernel/debug/dcc/../[list-number]/config + + where: + + + The address to be read. + + + The addresses word count, starting from address <1>. + Each word is 32 bits (4 bytes). If omitted, defaulted + to 1. + + + The bus type, which can be either 'apb' or 'ahb'. + The default is 'ahb' if leaved out. + + ii) Write instruction + + :: + + echo W > /sys/kernel/debug/dcc/../[list-number]/config + + where: + + + The address to be written. + + + The value to be written at . + + + The bus type, which can be either 'apb' or 'ahb'. + + iii) Read-write instruction + + :: + + echo RW > /sys/kernel/debug/dcc/../[list-number]/config + + where: + + + The address to be read and written. + + + The value to be written at . + + + The value mask. + + iv) Loop instruction + + :: + + echo L
... > /sys/kernel/debug/dcc/../[list-number]/config + + where: + + + Number of iterations + +
+ total number of addresses to be written + +
+ Space-separated list of addresses. + +What: /sys/kernel/debug/dcc/.../[list-number]/enable +Date: December 2022 +Contact: Souradeep Chowdhury +Description: + This debugfs interface is used for enabling the + the dcc hardware. A file named "enable" is in the + directory list number where users can enable/disable + the specific list by writing boolean (1 or 0) to the + file. + + On enabling the dcc, all the addresses specified + by the user for the corresponding list is written + into dcc sram which is read by the dcc hardware + on manual or crash induced triggers. Lists must + be configured and enabled sequentially, e.g. list + 2 can only be enabled when list 1 have so. -- cgit v1.3.1